3-5.IMPULSE G+ /VG+ S3可調變頻天車控制器IMPULSE G+ /VG+ S3 ADJUSTABLE FRENQUENCY CRANE CONTROLS-5
3-5.IMPULSE G+ /VG+ S3可調變頻天車控制器IMPULSE G+ /VG+ S3 ADJUSTABLE FRENQUENCY CRANE CONTROLS-5
3.IMPULSE G+ /VG+ S3可調變頻天車控制器(新英文版) 下載down load
IMPULSE G+ /VG+ S3 ADJUSTABLE FRENQUENCY CRANE CONTROLS(NEW
English Version)
Brake Test* Allows testing of available brake torque
Encoder Loss Detection* Signal loss detection at all times even when the motor is not rotating (during load float)
Snapped Shaft Detection* Detects a broken coupling shaft or discontinuity in the drive train
Slack Cable Detection* Identifies a slack cable condition and provides a selectable response (stop, slow down, alarm)
Roll Back Detection/Torque Proving Drive monitors brake functionality
at Start/Brake Check at Stop* and motor torque at start and stop
Safe Operating Windows Reduces the possibility of programming unsafe parameters
Load Check™ Reduces the possibility of lifting an overload
Quick Stop™ Reduces the possibility of load collision
Multi-Level Password Protection Limits unauthorized modification of drive parameters
Phase Loss Detection In case of output phase loss, brake will set immediately, retaining load
Control Interface Optically isolated quick disconnect 120 Vac control interface (24 Vac, 48 Vac, and 24 Vdc available) UL/cUL Rated
Tested and listed by Underwriters Laboratory
Ground Fault Short Circuit Protection Reduces damages to motor and drive
DC BUS Charge Indicator Indicates when the DC BUS has discharged to a safe level
Indexing* Allows precise programmed motor movement
Load Sharing* Allows two or more mechanically coupled motors to be controlled in a master/slave torque control fashion
Hook Height Measurement* Uses incremental encoder signal to determine hook height from calibrated position
Electronic Programmable Limit Switch* Allows slow down and stop limits without a geared limit switch
Automatic Reset Allows selectable conditions to be automatically reset
Over-Torque/Under-Torque Detention Allows programmable outputs and actions based on torque conditions
Slip Compensation Automatically compensates for motor slip
Motor Lead Reversal Electronically swaps motor leads for reverse operation
Keypad Copy Copy, store and write parameters from keypad
Communication Built-in RS-485 communication (Modbus - RTU)
Static Auto Tune Allows auto tune without mechanical disconnection
Enhanced Keypad Display Easily navigate and read diagnostics
Load Float™* Allows a load to be held aloft at zero speed without setting the electric brake
Weight Calculation* Enables load weight to be calculated with an accuracy of ±5% of full load (0–10 Vdc Output) X-Press Programming™ Allows programming initial setup in seconds
Swift-Lift™/Ultra-Lift™ Allows overspeeding with light loads or empty hook
Reverse Plug Simulation™ Allows operator to smoothly and quickly stop and change directions without setting parking brake
Stall Prevention Extends acceleration time and prevents the motor torque limits from being exceeded
Micro-Positioning™ Allows operator to make precise, slow movements
Multi-Function Input Terminals For end of travel/slow down, limits stops or other options
Flash Memory Stores last ten fault occurrences, even after power-down, for diagnostic purposes
Elapsed Time Counter Indicates actual time of operation (power on or run time)
Hoist Synchronization* Synchronizes multiple motors in master/slave configuration (speed matching)
Fault Storage Stores the last ten faults with trace data
Maintenance Timer Alerts operator when maintenance is required (run time) Programmable Fan Cooling fan on/off control selections for longer life Ambient Compensated Overload High ambient motor protection
Increased Drive Output Current Ratings Robust power section
Built-in Auto Tune Maximizes performance and life of motor (rotational or static)
Serial Communication Provides reliable digital linkage among various crane system peripherals, including Modbus, Modbus+, Profibus and Ethernet
Operation/Fault Display Simplifies setup and troubleshooting
* Features available on VG+ only