98014
點擊圖片放大商品名稱:
規格介紹:
全新量具-98014
規格介紹:98014
詳細介紹:
Item | Description | Brandnum | Model | Capacity | Accuracy | Quantity | ||
1 | Dial Gauge Series 700 | COMPAC | 733AB | 0-4" | 0.0005" | 4 | ||
2 | Dial Gauge Series 700 |
| " | 732B | 0-100MM | 0.01MM | 2 | |
3 | Dial Gauge Series 700 |
| " | 723AB | 0-2" | 0.0005" | 8 | |
4 | Dial Calipers |
| PEACOCK | 6350 | 0-6" | 0.001" | 50 | |
5 | Girod Tast Dial Indicator | TESA |
| 018.10010 | 0-100MM | 0.002MM | 19 | |
6 | Girod Tast Dial Indicator |
| " | 018.10006 | 0-0.4MM | 0.01MM | 20 | |
7 | Girod Tast Dial Indicator |
| " | 018.10008 | 0-0.25MM | 0.01MM | 17 | |
8 | Magnetic Base |
| VOYAGE | 49923 |
|
| 20 | |
9 | Indivialnel Micrometer | PEACOCK | 7025 | 0-25MM | 0.01MM | 20 | ||
10 | Point Micrometer | MITUTOYO | 112-177 | 0-1" | 0.001" | 15 | ||
11 | Point Micrometer |
| " | 112-178 | 1-2" | 0.001" | 3 | |
12 | Micrometer Head | HAUSNER | 8163 | 0-25MM | 0.01MM | 5 | ||
13 | Tempered Steel Thickness Gauge | HASBERG | 0.01x5M | 0.01x5M |
| 2 | ||
14 | Tempered Steel Thickness Gauge |
| " | 0.02x5M | 0.02x5M |
| 2 | |
15 | Tempered Steel Thickness Gauge |
| " | 0.03X5M | 0.03X5M |
| 2 | |
16 | Tempered Steel Thickness Gauge |
| " | 0.04x5M | 0.04x5M |
| 2 | |
17 | Tempered Steel Thickness Gauge |
| " | 0.05x5M | 0.05x5M |
| 2 | |
18 | Screw Thread Micrometer | MITUTOYO | 126-125 | 0-25MM | 0.01MM | 5 | ||
|
| " |
| " | 126-126 | 25-50MM | 0.01MM | 5 |
|
| " |
| " | 126-127 | 50-75MM | 0.01MM | 2 |
|
| " |
| " | 126-137 | 0-1" | 0.001" | 7 |
|
| " |
| " | 126-138 | 1-2" | 0.001" | 5 |
25 |
| " |
| " | 126-139 | 2-3" | 0.001" | 7 |
26 | Stainless Steel Rule | MSC |
| 06513006 | 6" |
| 45 | |
27 | Round Pocket Mirror | BIUE-PCINT | CF-143A | 17" |
| 20 | ||
更多商品
二手汽車粉碎機Car Shredding System-98013
Used Lindemann 1/1250 STV Car Shredding System & Non-Ferrous System For Scrap Car 50t/h Project: #98013 Used Lindemann 1/1250 STV Car Shredding System & Non-Ferrous System For Scrap Car 1. Built in 2000 and still running now. 2. Capacity of specification: 18~32T/Hr… (This is Lindemann’s ) But now the capacity of user is about 50T/Hr. 3. System included Lindemann 1/1250STV Shredding System & Non-ferrous System (Durable Equipment) 1.1 In-feed conveyor 1.2 Control System 1.3 Double roll compression feeder 1.4 1/1250STV Shredder 1.5 Vibration Absorbing System 1.6 Dedusting system 120.000m³/Hr 1.7 Trommel 1.8 Vibrator (Ⅱ) 1.9 Magnetic separator 1.10 Picking conveyor 1.11 Stacking conveyor 1.12 Wet scrubber & water tank 1.13 Conveyor 1.14 Trommel screen 1.15 Overband magnetic separator 1.16 Vibrator(Ⅲ) 1.17 Vibrator(Ⅳ) 1.18 E.C.S. recovery 1.19 Non-ferrous Control Room Basic data 4.1 1 (one) nonferrous metal separation plant, Lindemann system, type : NE-5P-BS For dry magnetic separation and processing of NF-metal and nonmetal mixtures from shredder plant. Input: 2~6 tons/hour Depending on the material to be processed And the percentage of the NF-metal included in the Infeed material. Grain size range of material to be handled: 3~65mm (100mm). 4.2 Capacity of nonferrous metal separator : Preparation of the nonferrous/nonmetal mixtures from the shredder plant: Separation of screened material (metals - nonmetals) Grain size Input: 3~12mm 2~3 tons/hour Rate of reclaimed metals: 93% (without cables and stainless steel) Metal content: 93% 12~30mm 2~4 tons/hour 30~65mm 3~5 tons/hour Rate of reclaimed metals: 95% (without cables and stainless steel) Metal content: 95% Preparation of material from heavy-media plants: Grain size: Input: Magnesium/rubber mixture 12~100mm 2 tons/hour Aluminum/stones mixture 12~100mm 4~5 tons/hour 97% or both end Separation efficiency: products. Aluminum/stones mixture 12~30mm 4~5 tons/hour 30~65mm 5~6 tons/hour 65~100mm 5~6 tons/hour Separation efficiency : 97~98% for both end products . Aluminum/stones mixture 3~12mm 3 tons/hour 4.3 Technical data and scope for supply : Item 1. Bunker and discharge vibrating conveyor For continuous, metered feeding of the plant. Technical data: Bunker: Volume : Feeding height : approx. 6m³ 3000mm Vibrating Feeding opening : 3000 x 1600mm Conveyor: Trough length : 4500mm Trough width : Trough height : Power required : 1100mm 250mm 2 x 1.3KW Scope of supply: - Bunker made of fabricated sheet steel, ribbed, top edge of hopper reinforced. - Supporting structure with reinforcements and supports for mounting the discharge vibrating conveyor. - Discharge vibrating conveyor, including drive. Item 2. Belt conveyor To transport the material from the bunker to the screening drum. Technical data: Shape of belt: Trough shaped Belt width: 650mm Conveying length: 10.0m Power required: 3.0KW Scope of supply: - Belt conveyor, stationary, with drive. - Feeding chute. Item 3. Overband magnetic separator: For magnetic separation of the nonferrous and non-metal material, lifting method of operation. Technical data: Belt width: 800mm Belt length: 1672mm Power required: 1.5KW Energization: 3.1KW, 70VDC Overall width: 1370mm Belt speed: 1.74m/s Scope of supply : - Overband magnetic separator, complete with drive and suspension device for height adjustment. - Supporting structure for suspending the overband magnet, with material guide chutes (partly of non-magnetic steel). Item 4. Screening drum For screening the nonferrous metal/nonmetal mixture into 3. Factions: 0~12mm, 12~65mm, and bigger than 65m. Technical data: Drum diameter: 1250mm Drum length: 5000mm Screening length: 3000mm approx. Screening hole diameters: 12mm and 65mm Power required: 3.0KW Scope of supply: - Screening drum with exchangeable screening plates, completely covered. - Frame with drum bearing, drive by gear motor. - Material guide chutes in the screening zones and at the drum outlet. - Supporting structure for mounting the drum on the foundation. - Maintenance platform at the drum outlet. Item 5. Belt conveyor (sorting belt) To transport the oversize fraction from the screening drum into containers . Technical data : Belt shape: Flat. Belt width: 650mm Conveying length: 10m Power required: 0.75KW Scope of Supply: - Belt conveyor, stationary, with drive. - Feeding chute - Sorting path, 4000 X 1000 mm. Item 6. Belt conveyor To transport the fraction smaller than 12mm into containers . Technical data : Belt shape : trough shaped Belt width : 400mm Conveying length : 8.0m Power required : 1.5KW Item 7. Belt Conveyor To transport the 12~65mm fraction to the NF-metal separator. Technical data: Belt shape: conveyor belt with corrugated side walls Belt width: 650mm Conveying length: 8.6m approx. Power required: 3.0KW Scope of supply: - Belt conveyor, stationary, with drive. - Feeding chute Item 8. Nonferrous metal separator, complete Technical data: Vibrating conveyors : trough length : trough width : trough height : 1650mm 500/600mm 150mm Nonferrous metal separator power required : 2 x 0.45KW Drive of conveyor belt : 2.2KW Drive of magnetic system : 5.5KW Item 8. Nonferrous metal separator - continued: Scope of supply : - NF-metal separator, model NF-5P, complete with drive, separating belt with supports and driving drum with incorporated rotating permanent magnetic system. - Vibrating conveyor, complete, with drive. - Supporting structure, completely encased by metal sheet on the separator level, with maintenance platforms and access stairs. - Material guide chutes underneath the separator. Item 9. Belt conveyor (sorting belt) To transport the waste fraction (rubber, wood, glass, stones, plastics) from the nonferrous metal separator into containers (to sort out stainless steel and copper cables). Technical data: Belt shape: flat Belt width: 500mm Conveying length: 7.5m Power required: 0.75m Scope of supply: - Belt conveyor, stationary, with drive. - Feeding chute. - Sorting path, approx. 1500 x 1500mm. Item 10. Belt conveyor (sorting belt) To transport the metal concentrate (A1/Sm-mixture) from the nonferrous metal separator into containers (to sort out manually brass and copper). Technical data: Belt shape: flat Belt width: 500mm Conveying length: 7.5m Power required: 0.75KW Scope of supply: - Belt conveyor, stationary, with drive. - Feeding chute. - Sorting path, approx. 1500 x 1500mm. Item 11. Electrical equipment For the control and switching of all motors and devices belonging to our scope of supply. Technical data: Max. connected load: 30KW approx. Operating voltage: 440 volts. According to VDE. Scope of supply: - Low voltage switch cabinet with 100A main switch including various in-situ control boxes and repair switches for the plant. - Operating buttons and mimic diagram are installed in the door of the switch cabinet. - Control is by means of programmable controller, SIMATIC S5-115U, make Siemens. - Cabling material from our switch cabinet. - Material according to VDE instructions. Table of Models and Output Figures of LINDEMANN Shredder Installations Shredder type Driving power Internal width of the housing Beating circle Output of Shredder scrap KW (PS/HP) mm mm t/h ZERDIRATOR 370 (500) 550 (750) 750 (1000) 1600 1750 6-10 9-18 10-20 1470 (2000) 2500 2100 30-50 I 370 (500) 750 (1000) 920 (1250) 2600 1750 9-13 15-25 18-32 II 1470 (2000) 1840 (2500) 2600 2100 30-50 35-60 III 2200 (3000) 2940 (4000) 2940 2500 40-75 50-100 Subject to modification in accordance with the latest technical development. LINDEMANN Shredder Plants in Operations for the Scrap Industry Since many tears and in many countries, LINDEMANN Shredder Plants transform complete derelict motor cars, sheared car body scrap (slabs), light bales, and miscellaneous scrap, such as refrigerators, stoves, washing machines, bicycles, and light sheet metal scrap , etc. into clean, dense and small-piece shredded scrap-a valuable raw material for the steel industry. LINDEMANN manufactures complete plants of different sizes designed for output figures from 6 to 150 tonnes per hour, including effective equipment for the charging of the material to be processed as well as for the cleaning, dedusting, and transporting of the shredded products. When processing derelict cars, one obtains, depending on their composition: 67-75% clean steel scrap 24-30% non-metallic waste 1.0-3.0% non-ferrous metals Shredded scrap produced by LINDEMANN Shredder Plants has the following features: y High density y A specific bulk weight of 1-2.5kg/dm3 y uniform pieces of an average size of 50-150mm y high quality and cleanness The non-metallic refuse (rubber, textiles, plastics, wood, dirt, sand, etc.) has an average bulk weight of 0.5 tonnes/m3. Just like household refuse, it is suitable for controlled tipping. LINDEMANN Machines and Plants for the Scrap Preparation Car Body Shredder Plants Shredder Plants for non-ferrous metals Dross preparation plants Car Body Squeezers Scrap Shears Scrap Baling Presses Crushers for Turnings Briquetting Presses Cast Iron Breakers The LINDEMANN Shredder System at a Glance LINDEMANN Shredder work according to a special system, the main feature of which is the grid-plate arranged above the rotor. For special requirements, however, a special shredder type “R” with upper grid-plate and additional basket type bottom grid can be supplied. The scheme shows the working method of the LINDEMANN shredder, the working cycles are: 1. Automatically controlled feed of charged scrap . 2. Tearing-off at the anvil edge . 3. Size-reducing at the baffle plate edge . 4. Densifying at the baffle plate , at the grid , and by impact with other scrap pieces . 5. Exit of shredded scrap pieces through the grid openings . 6. Sucking-off of flying dust and waste . 7. Discharge of the shredded scrap . 8. Ejection of coarse unshreddable pieces . Advantages of LINDEMANN Shredder Plants 1. Low foundation cost . 2. Low power consumption due to the smooth housing bottom and the milling-kind tearing effect of the hammers at the anvil edge . 3. Insensitivity against coarse pieces which cannot get stuck in the smooth housing bottom and which are ejected through the hydraulically operated ejection door without interruption of the production process . 4. High density of shredded scrap due to the scrap pieces rebouncing at the grid , at the baffle plate , and by impact with other scrap pieces . 5. Quick exchange of grid by simply pushing out the grid plate side-ways , this is of particular importance if scrap density is to be changed by substituting grids with different grid openings . 6. Long “fall” of the shredded scrap pieces from grid exit to shredder exit - which means maximum cleaning effect by means of the connected dust extraction . 7. Maximum flywheel energy due to the disc-type rotor , thereby reduction of current peaks during shredding . 8. Robust and wear-resistant feeding and charging equipment , scrap feed depending on the power in take of the shredder driving motor , thus , peak current and overcharging of the shredder are avoided , and a high output is achieved . 9. Highly wear-resistant lining of all parts of the shredder housing subjected to strong wear with easily exchangeable wear parts . Disc-rotor with exchangeable wear-resistant wear caps . Shredder size II , with steel belt feeding conveyor , driving power 1840KW Shredder size III , driving power 2940KW Scheme of a Car Body Shredder Plant 1. Feeding chute with tilting table. 2. Shredder, 3. Main drive motor. 4. Vibration absorber. 5. Hammer dismantling 6. Control 7. Vibrating conveyor. 8. Belt conveyor. 9. Separating drum. 10.Magnetic drum. 11.Steel sorting belt. 12.Steel discharge belt. 13.Dust belt. 14.Dust discharge belt. 15.Non-ferrous metal sorting belt. Dust extraction equipment. Here some details Every detail counts if a shredder plant shall work trouble-free and give highest performance. We know how every detail must be designed and carried out by our experience gained in the construction of many shredder plants. 1. The shredder housing is hydraulically tiltable at the rotor centre line to give easy access to the interior of the shredder. Arrangement can also be made for the rotor to be lifted with the housing top. 2. Due to the wear-resistant protection caps fitted to the rotor, build-up welding of the rotor discs is no longer necessary. 3. The hydraulic device for dismantling the hammer axles facilitates the exchange of hammers and reduces maintenance 4. The control desk is designed for simple and safe control of the whole plant automatic supervision of all electric drives and instruments with indication of their operation on a luminous 5. Separating drum with dropping 6. Magnetic separating station with following steel sorting conveyor. 7. Slewable belt conveyor for the discharge of clean shredded steel scrap on to stockpile or for direct loading into LINDEMANN Shredder plants Serve the Environmental Protection They do away with derelict motor cars and ugly mounds of mixed scrap, they work ecologically beneficial, vibration-free, without dust. By means of noise protection equipment, the noise level can be reduced to values officially prescribed. Sound absorbing walls around a shredder plant. Vibration absorbing units especially developed for LINDEMANN Shredders prevent the transmission of vibrations and keep foundations costs low. Dust extraction equipment developed by LINDEMANN ensures dust-free shredding, conveying, and loading of the shredded products. The degree of purity of the exhaust air complies with all statutory provisions. Operation instruction A.1 Introduction A1.2 Basic information Materials suitable for shredding Maximum thickness of material: For sheet metal plates: 2mm For sectional steels and pipes: 5mm wall thickness For rounds: 10mm Important to note: Please avoid by all means to only charge material having there maximum dimensions. Such material should be fed into the shredder in small quantities only, most preferably mixed with other light scrap. Materials unsuitable for shredding - Wire bales and wire ropes (danger of accident-danger of shredder exit getting chocked and blocked). - Long flats or strip-shaped sheet-metal sections in a length ranging from approx. 3 meters onward when they are charged in larger quantities (danger of overfeed of shredder). - Receptacles (containers) or items containing explosive, inflammable, toxic or corrosive substances in liquid, dust-like or gaseous condition (danger of explosion, danger of accident), in particular, keep receptacles or containers from the chemical and colour producing industry away from the shredder, because: (a) Their content - even if only small residual quantities are involved - in most cases, is highly explosive and toxic. (b) Because cans (canisters) and receptacles are partly tinned, so that they would increase the tin content of the shredded scrap beyond the admissible limit. Preferably, the shredder is used for: - Car bodies - Stoves, refrigerators, washing machines, steel furniture for offices and similar items. - Stampings and light destructor scrap (collected light iron scrap). How to prepare the car bodies: Car bodies are only allowed to be fed into the shredder after having been prepared in a dequate manner. The old cars must be freed from the following items: Liquefied petroleum gas tanks - In view of the highly explosive gas mixture which in case of explosion would lead to damaging of the dust extractor equipments. Ty res - Because of their steel liners which cause the various tyre pieces to drop on to the steel scrap conveyor-belt instead of being directed to the waste belt by means of the subsequently operating magnetic drum. The following elements should be removed from the old cars: Motors and gears - In view of the high portion of alloyed material the steel mills do not like to find in the ultimate or end products. - Because of the increased wearing effect in the shredder. - In view of contamination of the oil (oil mud deposits in the pipe system). Car sets (if the shredder installation does not feature a separating drum) - On account of the optically seen poor appearance of the shredded scrap, with hooked-on bolster and textile waste. Note: Gasoline tanks either have to be removed completely or perforated in such a way that no gasoline remnants are still in them (please refer for this to it, “unsuitable materials for the shredder”). Liquefied petroleum gas tanks shall be removed completely because the stuff contained in them would produce a highly explosive gas mixture in the shredder, and as a consequence, the entire dust extractor equipment would be exposed to the danger of damaging (please refer for this also to “how to prepare the car bodies”). Batteries and radiators have to be removed if not done already by the scrap car suppliers on account of their good sales price. Car bodies can be processed both in pre-squeezed and unsqueezed condition. Axles, springs and wheels can be shredded together with the car bodies. So called car body slabs are, in general, not suitable for being shredded because the shredder may be overstressed by them and increased current peaks may occur. In any event, the portion determined for the car body slabs to be processed should remain within a justifiable limit. Caution: The shredding of scrap bales is to be strictly excluded coarse items contained in the bales are neither detectable nor can they be removed. Therefore, there would be complete breakdown of the installation on account of rupture caused by coarse items.
二手軋鋼機Used Morgan Rod Mill-98011
Used Morgan Rod Mill for Sale Project#98011 Brief Introduction Of Used Morgen Rod Mill. a. Start Up In 1977. Original Design Capacity : 300,000T/yaer Curre nt production : 720,000T/year Capacity Of Reheating Furnace : 100T/hour Maternal : 100mm x 100mm-118mm x 118mm x 10-14.2m e. Speed : 14.2m/s (13 mm rod) , to 80mm/s (5.5mm rod) Product : 5.5m~13 mm dia. g. Unit Weight : 1500Kg/coil Condition : Still Running Will Be Shutdown In 2010. 2 Content Rod Mill Layout ...............................................................................3-4 2. Rod Mill Flow Chart ...........................................................................5 Brief History ....................................................................................7-8 Main Equipments ...............................................................................9 Included Reheating Furnace ...............................................................9 Roughing Mill ....................................................................................10 Intermediating Mill .................................................................................11 Finishing Mill .....................................................................................12 Cooling Box .......................................................................................13 Inclined Laying Head ........................................................................13 Stelmor Conveyor .............................................................................14 Coil Ring Collecting Device ...............................................................15 Coil Binding Machine ........................................................................15 Electric ...............................................................................................16 Roll Manage ......................................................................................16 Material ............................................................................................17 Product .............................................................................................18 3 Rod Mill Layout Table FURNAC Finishing RSM Shipping Area Laying Head Charging Bed Roughing Intermediate Finishing RSM Laying Head Rod Mill Layout Roughing Stand Intermediate stand Finishing Block Mill Reducing Sizing Mill Stelmor Conveyor : Shear : Cooling Box : Inclined Laying Head : Reforming Tub. : Coil Downender : Hook to Hook Machine : Coil Banding Machine : Weigher : Coil Unloader ROD MILL FLOW CHART Roughing Mill Intermediate Mill Finishing Mill RSM Laying Head Shipping Area FURNACE Finishing Mill RSM Laying Head As Roll Coil Pickling & Coating Drawing Cold Heading Drawing Wire Annealing Cold Heading Wire BRIEF HISTORY MAIN EQUIPMENTS MATERIAL PRODUCTS BRIEF HISTORY START UP- IN 1977 CAPACITY- DESIGNED ANNUAL RODUCTION： ORIGINAL DESIGN ： 300,000 Tons/Year CURRENT PRODUCTION： 720,000 Tons/Year HISTORY : Rod mill at AA Corporation was commissioned in May 1977, with designed annual capacity of 300,000 tons. Material Stock is rolled through a two-strand straightway roughing and intermediate mill consisting of 15 horizontal stands, and finished after two individual offset finishing block. Each finishing block is composed at 10-Stand no-twist finishing mill and a Stelmor controlled cooling line. From the delivery end of the cooling line, the rod is coiled, bundled and transported to the shipping area by a power and free conveyor system. The mill has the capability of producing various sizes of rod from a 118 mm square billet of 14.2m long. It is capable of delivering product at speeds ranging from 14.2m/s(13 mm rod) to 70 m/s (5.5 mm rod). We modernized the mill and speed up the maximum finishing speed from 50.8 m/s to 70 m/s in 1985, we modified the existing Stelmor fan to VVVF control in 1992, leading to the electricity saving annually. Since 1996, we have begun to modernize the mill again and expect to speed up the maximum finishing speed from 70 m/s to 80 m/s. To achieve this object, Morgan corporation has introduced 4-stand Rod TEKISUN Reducing/Sizing mill(RSM) after the No-Twist mills with all other required upgrading equipment of latest technology. The benefit of the RSM is that rolling at 54 t/h with single family roll pass and with provide additional over 60,000 tons per year, and more precise tolerance up to plus/minus 0.1 mm . 9 PUSHER TYPE CAPACITY : 100 Ton/Hr EFFECTIVE DIMENSION : 15.7M(L) ¯ 14.9 M(W) COMBUSTION : HEATING ZONE ¯ 1 SOAKING ZONE ¯ 3 A. ROUGHING 7 STANDS 2 STRANDS TIED STANDS 4/5, 6/7 MOTOR POWER : Std. 1~3 300HP, Std. 4/5 700 HP, Std. 6/7 1500HP Max. ROLL DIAMETER Std. 1~2 Ø525 mm, Std. 3~5 Ø460 mm, Std. 6~7 Ø400 mm, CROP SHEAR AFTER Std.#7 CROP SECTION 40 mm B. INTERMEDING 8 STANDS 2 STRANDS TIED STANDS 8/9 MOTOR POWER : Std. 8/9 1500HP, Std. 10~15 700HP Max. ROLL DIAMETER : Std. 8~9 Ø400 mm, Std. 10~15 Ø300 mm CROP/CHOP SHEAR AFTER Std#15 SIDE LOOPER BETWEEN CROP/CHOP SHEAR AND F/M 10 STANDS 2 LINES V-ARRANGEMENT MOTOR POWER : 1500 HP ¯ 2 / LINE Max. ROLL DIAMETER : Std. 16~17 Ø210 mm, Std. 18~25 Ø158 mm. 2 ZONES WATER BOX AFTER NTM LENGTH 15 M ( DIVIED 3 SECTIONS ) WATER CONSUMPTION : 0~7604 L/Min FOR 1 STRAND. AFTER NTM INCLINED LAYING HEAD CONE TYPE, INCLINED ANGLE 7.5°. 70/140 HP, 550/1300 rpm. LAYING PIPE O.D 48.6mm, I.D 34.4 mm STPA26 FRONT & TAIL POSITIONING CONTROL CHAIN TYPE, TOTAL LENGTH 44 M WITH IMPROVED DECK PLATE FORCED AIR 6-ZONES/STAND (36M) 6 – BLOWERS / STRAND VVVF AC MOTOR SAIL TYPE REFORMING TUB COIL O.D 1250mm, I.D 850mm Max. COIL WEIGHT : 1500kg COIL BINDING MACHINE 4-BONDS COMPACTOR ANALOG CONTROL BY MILL TRACKING COMPUTER SYSTEM SIZE : 100mm ¯ 100mm, 118mm ¯ 118mm UNIT WEIGHT : 75.95 Kg/m (FOR ⃞100 mm) 106.46 Kg/m (FOR ⃞ 118 mm) LENGTH : 10.0m~14.2m PRODUCTS ROD IN COIL SIZE : FINISHING METAL DIMENSION : Ø5.5mm~Ø13mm UNIT WEIGHT : 1500 Kg GRADE : CARBON STEEL , LOW ALLOY STEEL WELDING, TOOL STEEL, FREE CUTTING TIRE CORD , PC WIRE AND STAINLESS STEEL etc.
二手軋鋼設備Used Bar Mill-98009
New, Unused Spare Rolling Mill & Melt Shop Equipment Project#98009 1. Bar cropper for cold cuts (billet shear) Maker : Erfurt (W.G.) cutting force : 1000tons 2. Roughing roll stand a. Pomini : 2sets , 650T b. Danieli : 2sets , 750T 3. Pneumatic Tie machine a. Small package for steel bar 3sets b. Large package for steel bar 1set Maker : Danieli 4. Straightening machine for section bar Maker : Danieli 5. 4sets train finishing mill Roll diameter : 270ψ Maker : Danieli 6. Turning conveyor for coiler 4sets Maker : Danieli 7. (Blower) (Fan) for cell cooling conveyor Maker : Danieli Quantity : 12sets 8. CNC lathe for cutting roll Maker : Japan Length : 2.5M 9. Lubricating system tank for rolling requirement Maker : Japan 2sets 10.Tension test machine 1set Capacity : 100Ton 11.Hydraulic equipment for rolling requirement Same sets 12.Hydraulic cylinder for rolling requirement One sets File Kuokihu
二手軋鋼設備Used Bar Mill-98004
Project No. 98004 TECHNICAL PROPOSAL FOR 300,000T/Y USED BAR ROLLING MILL EQUIPMENT 50 T/ HR CONTENTS 1. GENERAL 1.1 PREFACE Remark: This bar m ill is on operati on now , Capacity :300, 0 00TO N ， Built in 1984, was made b y TANAKA Japan, capacit y 30TON/HR ROLLING MILL ， in 2006 invested USD4,000,000 revamping and Mo de fie d to (1). new 60TON/HR REHE AT ING FURNACE, Material is billet in SQ100m m、SQ120m m、SQ130m m、SQ150m m、SQ160m m ; (2)new 650m m ∮ BREAKING DOWN MILL × 3set; (3)6 PA SS ROUGH MILL changed to DC MOTO R DRIVE × 3set ; (4) 6 PASS INTERMEDI ATE MILL REDUCE GEAR c h ang e to straig ht lin e ; (5 ) 6 PA SS FIN ISH I NG MILL change d to DC MOTOR DRIVE × 4set to increase production speed ; (6) new packing line ， BAR AUTO BUNDLING MACHINE OF SUND BRIS TA SWEDEN, Capacity upgrade to 50TON/HR ， Due to new bar m ill in northe rn Ta iwan, , It wi l l be shut down i n m i d 2013 The following description is the rolling mill equipment with an annual production capacity of 300,000 TON, the original equipment was built in 1984 by Tanaka Co., Ltd. from Japan, and provides an original production of 30TON/HR ROLLING MILL, And invested a capital of USD4, 000,000 in 2006 to updated equipments; (1 ) A new 60TON/HR REHEATING FURNACE uses raw materials of SQ100mm, SQ120mm, SQ130mm, SQ150mm, SQ160mm BILLET; (2) A new 650mm ∮ BREAKING DOWN MILL × 3set; (3) 6 PASS ROUGH MILL replaced DC MOTOR DRIVE × 3set ; (4) 6 PASS INTERMEDIATE MILL REDUCE GEAR replaced with tallied inline mill gear ratio; (5) 6 PASS FINISHING MILL replaced DC MOTOR DRIVE × 4set to change the production rate; (6) A new automated packaging lines, with an additional BAR AUTO BUNDLING MACHINE OF SUND BRISTA SWEDEN and other production processes to achieve the present production capacity 50TON/HR. Due to a building of a new plant, and is expected to go into operation in August 2010; The equipment mentioned above are to be stop of production, all machineries and equipments are for sale, and should empty the factory at the end of 2010. The following description is the rolling mill equipment with an annual production capacity of 300,000 TON, the original equipment was built in 1984 by Tanaka Co., Ltd. from Japan, and provides an original production of 30TON/HR ROLLING MILL, And invested a capital of USD4, 000,000 in 2006 to updated equipments; (1 ) A new 60TON/HR REHEATING FURNACE uses raw materials of SQ100mm, SQ120mm, SQ130mm, SQ150mm, SQ160mm BILLET; (2) A new 650mm ∮ BREAKING DOWN MILL × 3set; (3) 6 PASS ROUGH MILL replaced DC MOTOR DRIVE × 3set ; (4) 6 PASS INTERMEDIATE MILL REDUCE GEAR replaced with tallied inline mill gear ratio; (5) 6 PASS FINISHING MILL replaced DC MOTOR DRIVE × 4set to change the production rate; (6) A new automated packaging lines, with an additional BAR AUTO BUNDLING MACHINE OF SUND BRISTA SWEDEN and other production processes to achieve the present production capacity 50TON/HR. Due to a building of a new plant, and is expected to go into operation in August 2010; The equipment mentioned above are to be stop of production, all machineries and equipments are for sale, and should empty the factory at the end of 2010. THE STEEL GRADES WHICH ARE TO BE PROCESSED ON THE MILL ARE AS FOLLOWS. A). DEFORMED BAR : D10~D40 STEEL BARS, APPLICABLE STANDARDS: JIS 20-2525＆24-2536 “ROLLED STEEL FOR GENERAL STRUCTURE” B). RUNG BAR : ∮9.5mm～∮40mm STEEL BARS JIS G 3101&JIS G4051 C). PRODUCT LENGTH OF BARS: 12M OR OTHERS LAYOUT : VPLEASE REFER TO ATTACHED GENERAL LAYOUT. 1) .ROLLING MILL : THE BILLET IS CHARGED ON THE BILLET CHARGING BED BY THE BILLET YARD CRANE, AND TRANSFERRED TO THE PUSHER TYPE 60 TON/HR REHEATING FURNACE BY THE BILLET CHARGING ROLLER TABLE. AND THE HEATED BILLET ARE DISCHARGED FROM REHEATING FURNACE MAIN PUSHER AND PROCESSED THROUGH ROUGHING MILL TRAIN, INTERMEDIATE TRAIN, FINISHING MILL TRAIN。 THE ROLLING MILL COMPRISES A TOTAL OF 21 STANDS，DIVIDE IN BREAKING DOWN MILL WITH 3 STANDS (3PASS)，ROUGHING MILL WITH 6 STANDS (6 PASS), INTERMEDIATE MILL WITH 6 STANDS (6 PASS), FINISHING MILL WITH 6 STANDS (6PASS). THE ROUGHING ROLLING MILL BY THE 3 SET MONOMER DRIVEN BREAKING DOWN MILL ARE ROLLER BEARING 3PASS AND 3SET ONE INLET TO TOW OUTLET DRIVEN ROUGH MILL ARE FIBER BEARING 6 PASS FORMED，DRIVEN ARE DC MOTOR，INTERMEDIATE MILL ARE 3SET ONE INLET TO TOW OUTLET DRIVEN INTERMEDIATE MILL ARE ROLLER BEARING 6 PASS FORMED，DRIVEN ARE AC MOTOR，BUT THE FINISHING ROLLING MILL ARE 2SET ONE INLET TO TOW OUTLET DRIVEN FINISHING MILL ARE ROLLER BEARING 4 PASS AND 2 SET MONOMER DRIVEN FINISHING MILL ARE ROLLER BEARING 2PASS FORMED， DRIVEN ARE DC MOTOR，ALL STANDS ARE ARRANGED IN HORIZONTAL ARRANGEMENT. 2) .COOLING BED: ON THE WAKING BEAM TYPE 6MtrW×55MtrL COOLING BED, MAIN COMPONNENTS ARE 4 STRANDS RUN IN ANGLE, BREAK, KICK OFF, FIXED RAKES, MOVABLES, DRIVE GROUP, RUN OUT DEVICE , PRODUCTS ARE COOLD DOWN TO DESIRED TEMPERATURE, WHILE MAINTAINING THE STREIGHTNESS. 3) LENGTH CUTTING & FINISHING BUNDLING SYSTEM FOR DEFORMED BAR. THOSE PRODUCTS ARE THEN DISCHARGED FROM THE COOLING BED AND FURTHER PROCESSED BY LENGTH CUTTING AND FINISHING BUNDLING SYSTEM. ALL PRODUCTS ARE CUT TO LENGTH BY CUT FORCE D32×12Apcs (400TON) COLD SHEAR TRANSFERRED TO RECEIVING CONVEYOR. AT THE END OF THE CONVEYOR，A CONVEYED TABLE IS LOCATED WHICH TRANSFER THE PRODUCTS TO BUNDLING AREA TO SHIPPING AREA。 1.2 PLANT DESCRIPTION This mill has the area 24,000 ㎡， st ruc t ure plant Wi dth(20M +14M+16M) × Lenth240M=12,000 ㎡， straig ht lin e desi gn ， all machineries are horizontal mills : The original construction of the steel plant is 24, 000 square meters of land , The steel plant itself Wi dt h(20M+14M+ 16M ) × Lent h240M = 12, 000 ㎡ , Inli ne desi gn, all m a chineries are horizontal mills, con t en ts and specifications of major eq ui pm ents as on be low : 1.2.1. 60TON/HR REHEAT ING FURNACE EQUIPMEN T; 1.2. 2. T Y PE: PU SHER TYPE ; TO P & LOWER 3 ZONES HE AT ING 1.2. 3. EFFECTIVE FURNACE LENGTH: 19,500 m m ; WIDTH: 6, 700mm 1.2.4. FUEL: HE AVE OIL 28LITER / TON (CONTINUOUS PRODUCTION) 1.2. 5. B U RNER: TO P HE AT ING ZONE 1,800L /HR × 6SET; TO P SOKING ZONE 800L/HR × 3SE T; LOWER SOKING ZONE 800L /HR × 3SET; TO TA L BUENER 12SET WITH PREHE ATING HOT AIR 1.2. 6. H O T WIN D FUEL DUCT: BLOWER 150HP /590Nm 3 /min; RECUPER ATOR: 500 ℃ / 18, 926 Nm 3 /min; 1.2.7. BILLET CHARGE BED 6M × 2SET: CHAIN TYPE 5Mw × 4, 5Ml/MAX34TON /SPEED5,2M/m in 1.2.8. BILLET CHARGE ROLLER TABLE: AC MOTO R WITH INVERTER/34Ml/ SPEED43M/min 1.2.9. MAIN PUSHEAR WITH HYDR AULIC UNIT: FORCE 47,000KG/set × 2set(WORKING PRESSURE:120 kg/cm 2 , CYINDER: TC224mm ∮× S T 70 0 mm × 2set ) 1.2.10. SIDE PUSHEAR WITH COOLING WATER: FORCE 2,200KG (MAX), INSIDE WATER COOLIN G. 1.2. 11 .C HIMNEI SPECIFIC ATION: TO P ID 1600mm ∮ ; LOW E R ID2500m m ∮ ; HIGH 40Mtr. 1.2.12.BILLET: SQ100mm 、 SQ120mm 、 SQ130m m 、 SQ150mm 、 SQ160m m . 1.3. 1. BREAKING DOWN MILL EQUIPMENT 3SE T; 1.3. 2. M A IN EQUIPMEN T SPECIFIC AT IO N ITEM NO. TYPE POWER HP GEAR R ATIO ROLLER DIA REMARK BD1(K1) 2HI HO RIZON VAL DC600HP 1/ 60.45 ∮ 650m m × 600mm L 2006 TANAKA JA PAN BD2(K2) 2HI HO RIZON VAL DC600HP 1/ 45.14 ∮ 650m m × 600mm L 2006 TANAKA JA PAN BD3(K3) 2HI HO RIZON VAL DC600HP 1/ 33.65 ∮ 650m m × 600mm L 2006 TANAKA JA PAN 1.4. 1. R O UGH MILL EQUIPMENT 6SE T: 1.4. 2. M A IN EQUIPMEN T SPECIFIC AT IO N ITEM NO. TYPE POWER HP GEAR R ATIO ROLLER DIA REMARK RM1(K4) 2HI HO RIZON VAL DC600HP 1/ 28.37+ 1/ 1. 7 ∮ 410m m × 1000mm L 1985 TANAKA JA PAN RM2(K5) 2HI HORIZON VAL 1/ 28.37+ 1/ 1. 2 ∮ 410m m × 1000mm L 1985 TANAKA JA PAN RM3(K6) 2HI HORIZON VAL DC600HP 1/17.476+1/1.41 ∮ 410m m × 1000mm L 1985 TANAKA JA PAN RM4(K7) 2HI HORIZON VAL 1/17.476+1/1.14 ∮ 410m m × 1000mm L 1985 TANAKA JA PAN RM5(K8) 2HI HORIZON VAL DC800HP 1/ 4. 29+ 1/3. 24 ∮ 410m m × 1000mm L 1985 TANAKA JA PAN RM6(K9) 2HI HORIZON VAL 1/ 4. 29+ 1/2. 28 ∮ 410m m × 1000mm L 1985 TANAKA JA PAN ※ WITH INLET GUIDE THROUGH & OUTLET GUIDE 1.5.1. INTERMEDI ATE MILL EQUIPMENT 6SE T: 1.5. 2. M A IN EQUIPMEN T SPECIFIC AT IO N ITEM NO. TYPE POWER HP GEAR R ATIO ROLLER DIA REMARK IM1(K10) 2HI HO RIZON VAL AC800HP 1/ 5. 39+ 1/1. 74 ∮ 285m m × 800mm L 1985 TANAKA JA PAN IM2(K11) 2HI HORIZON VAL 1/ 5. 39+ 1/1. 316 ∮ 295m m × 800mm L 1985 TANAKA JA PAN IM3(K12) 2HI HORIZON VAL AC800HP 1/ 5. 39+ 1/1.265 ∮ 300m m × 800mm L 1985 TANAKA JA PAN IM4(K13) 2HI HORIZON VAL 1/ 5. 39+ 1/1 ∮ 305m m × 800mm L 1985 TANAKA JA PAN IM5(K14) 2HI HORIZON VAL AC800HP 1/ 3. 139 ∮ 285m m × 800mm L 1985 TANAKA JA PAN IM6(K15) 2HI HORIZON VAL 1/ 2. 583 ∮ 295m m × 800mm L 1985 TANAKA JA PAN ※ WITH INLET GUIDE THROUGH & OUTLET GUIDE 1.6. 1. FINISHIN G MILL EQUIPMENT 6SE T: 1.6. 2. M A IN EQUIPMEN T SPECIFIC AT IO N ITEM NO. TYPE POWER HP GEAR R ATIO ROLLER DIA REMARK FM1(K16) 2HI HO RIZON VAL DC600HP 1/ 3. 2 ∮ 303m m × 800mm L 1985 TANAKA JA PAN FM2(K17) 2HI HORIZON VAL 1/ 2. 37 ∮ 295m m × 800mm L 1985 TANAKA JA PAN FM3(K18) 2HI HORIZON VAL DC1,000HP 1/ 2. 179 ∮ 295m m × 800mm L 1985 TANAKA JA PAN FM4(K19) 2HI HORIZON VAL 1/ 1. 641 ∮ 285m m × 800mm L 1985 TANAKA JA PAN FM5(K20) 2HI HORIZON VAL DC800HP 1/ 1. 4 ∮ 285m m × 800mm L 1985 TANAKA JA PAN FM6(K21) 2HI HORIZON VAL DC800HP 1/ 1. 22 ∮ 295m m × 800mm L 1985 TANAKA JA PAN 1.6.3. OTHER EQUIPMENT: HOT BILLET SHEAR × 1SET/ HYDRAULIC TYPE 、 F LYING SHEAR F O R ROU GH MILL CUTTING HEAD × 1SET / 55m m S Q/1. 125M / S EC 、 F LYING SHEAR FOR INTERMID ATE MI LL CUTTING HEAD × 1SET / 30m m S Q/4M /SEC 、 PINCH ROLLER × 4SE T. ※ WITH INLET GUIDE THROUGH & OUTLET GUIDE ※ SPEED OF THE FINAL PRODUCT 9.5Mtr/sec FOR D12mm 1.7. 1. C OOLING BED EQUIPMENT 6MtrW × 55MtrL: 1.7. 2. M A IN EQUIPMEN T SPECIFIC AT IO N 1.7.3. TYPE:4 STRANDS OPEN RUN IN ANGLE WITH BRAKE & KICK OFF SYSTEM 1.7.4. 55MtrL COOLING BED WITH FIXED RAKE S、MOVING RAKE S、ALIGNING ROLLERS WITH DRI V E 、 CAMS DRIVE GROUP AND RUN OUT DEVICE ROLLER TA BLE. 1.7.5. PRODUCT SPECIFIC ATION: D10 ∮～ D40 ∮ 1.7. 6. W O RKING TEMPER ATURE: MAX950 ℃ 1.7. 7. W O RKING TIME: 1.85 SEC/ CYCLE 1.8.1. LENTH CUTTING & FINISHING SYSTEM FOR DEFORMED BAR: 1.8. 2. M A IN EQUIPMEN T SPECIFIC AT IO N 1.8.3.COLD SHEAR: CUT FORCE D32 × 12pc s(400TON); C Y CLE 15/m in; BL ADE SIZ E 50 × 100 × 80 0 mm; BLA D E M ATERIAL SKD11; 1.8.4. LENGTH CUTTING MECHANISM: MOVING STOPER TYPE; MAX WORKING LENGTH20Mtr; 1.8.5. AFTER COLD SHEAR ROLLER TA BLE: LENGT H20Mtr; TRANSFER SPEED 0.18M/SEC; MOTO R 3H P. 1.8. 6. SMALL BUNDLE MACHINE × 4SET: HYDRAULIC TYPE; WORKING DIA/ ∮ 20mm ～∮ 200mm; WORKING SPEED: 4SEC/CYCLE; MANUFACTURER : TA TON JA PAN; M ATERIAL: 3.2mm ∮ WIRE ROD 1.8.7. LARGE BUNDLE MACHINE × 1SET: TYPE SUND BIRS TA SWIDEN KNSB-6/650; WORKING DIA/ ∮ 300m m ～∮ 400mm ; WORKING SPEED: 7SEC /CYCLE; M ATERIAL: 5.5mm ∮ WIRE ROD 1.8.8. BUNDLING LINE ROLLER TABLE × 4SET: CHAIN TYPE; LENGTH55Mtr × 1 、 16M tr × 3; MOTO R15H P × 1 、 10H P × 4 、 5HP × 2 、 2HP × 14; TRANSFER SPEED 5M/SEC; ROLLER PICH: @1,200mm 2.1.1. PUBLIC SYSTEM EQUIPMEN T: 2.1. 2. M A IN EQUIPMEN T SPECIFIC AT IO N 2.1.3. COMPRESSORS: TYPE SCREW; POWER150HP × 3SET/1#,8#,9# 、 60HP × 4SE T /2#,3#, 4#, 5# 、 100HP × 2SET/6#,7#; MANUFACTURER : FUSEN TA I WAN; 2.1. 4. INDIRECT WATER PUMP × 4SET: VERT ICAL CENTRIFUGAL TYPE FST; MOTO R40H P/ 3 ∮ / 60HZ / 4P/ 2 20 V; PUMP150CMH/ 45MH / 150m m D IA 2.1. 5. DIRECT WATER PUMP × 4SET: HORIZON TAL CENTRIFUGAL TYPE FSBL; MOTO R50H P/ 3 ∮ / 60HZ /4P/ 2 20 V; PUMP180CMH/ 65M H / IN125m mDIA/OUT100m mDIA 2.1.6.SCALE WATER OUTLET PUMP × 3SET: ITEM MA 、 MB 、 MC; ENERGY 25 MHEAD/2M 3 /M IN; MOTO R50H P/ 3 ∮ / 60HZ / 4P/ 2 20 V; PUMP IN125m mDIA/OUT125m mDIA 2.1.7. SCALE WATER RETURN PUMP × 2SET: ITEM M43 、 M44; ENERGY 25M H E AD / 5M 3 / MIN; MOTO R50H P/ 3 ∮ / 60HZ / 4P/ 2 20 V; PUMP IN200m mDIA/OUT200m mDIA 2.1. 8. C OOLING WATER PUMP × 5SET: ITEM M39 、 M40 M41 、 M42 M 4 2A; ENERGY 25M H E AD/2.5M 3 /MIN ; MOTO R25H P/ 3 ∮ / 60HZ / 4P/ 2 20 V; PUMP IN125m mDIA/OUT150m mDIA 2.1. 9. C OOLING TO WER PUMP × 2SET: ITEM M47 、 M48; ENERGY 25M H E AD/2.5M 3 /MIN ; MOTO R20H P/ 3 ∮ / 60HZ / 4P/ 2 20 V; PUMP IN100m mDIA/OUT125m mDIA 2.1.10. E.O. T. CRANE: A1. SPAN 18.925M / 7.5T E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 7.5 ㄨ 1.05M 18.925M SPEED (M/Min) 5.2 ㄨ 15 60 POWER (KW) 15 ㄨ 0.4×2 15 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 8 ㄨ WIRE DIA. 14 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 A2. SPAN 18.925M / 10T E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 10 ㄨ 1.595M 18.925M SPEED (M/Min) 4.8 ㄨ 15 30 POWER (KW) 11 ㄨ 0.4×2 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 8 ㄨ WIRE DIA. 16 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 A3. SPAN 18.925M / 7.5T E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 7.5 ㄨ 0.82M 18.925M SPEED (M/Min) 5 ㄨ 15 30 POWER (KW) 7.5 ㄨ 1.1 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 14 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 B2、B3、B5 .SPAN 12.715M / 5T × 3SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 5 ㄨ 0.82M / 0 78M / 0.78M 12.715M SPEED (M/Min) 5 ㄨ 15 30 POWER (KW) 7.5 / 6 / 5.5 ㄨ 0.4×2 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 12 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 B4、B6 SPAN 12.715M / 7.5T × 2SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 7.5 ㄨ 1.05 / 0.82M 12.715M SPEED (M/Min) 5 ㄨ 15 30 POWER (KW) 7.5 / 11 ㄨ 0.4×2 /1.5×1 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 14 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 C1 SPAN 14.695M / 5T × 1SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 5 ㄨ 0.942M 14.695M SPEED (M/Min) 8 ㄨ 15 30 POWER (KW) 20 ㄨ 3.75×2 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 12 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 C2、C3、C4 SPAN 14.695M / 10T × 3SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 7.5 ㄨ 1.6M 14.695M SPEED (M/Min) 6 / 6 / 4.8 ㄨ 15 30 POWER (KW) 15 / 15 / 11 ㄨ 0.75×1 / 0.75×1 / 0.4×2 3.75 / 3.75 / 7 5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 8 ㄨ WIRE DIA. 16 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 3.1. 1. S PARE PA RT S EQUIPMEN T: 3.1. 2. BREAKING DOWN MILL ROLLER × 2SET / 12pcs: DIA∮ 650m m × 600mmL ROLLER BEARING TYPE. 3 . 1 . 3 . ROUGH MILL ROLLER × 2SET / 24pcs: DIA∮ 410mm × 1,000mmL FIBER BEARING TYPE. 3.1. 4. FIBER BEARING FOR ROUGH MILL × 2SET / 24pcs. 3.1. 5. INTERMEDIATE MILL STAND WITH ROLLER、CHOCK & BEARIMG × 6SET: DIA3 0 0 m m × 800mm L . 3 . 1 . 6 . INTERMEDIATE MILL ROLLER × 2SET / 24pcs: DIA300m m × 800mm L 3.1. 7. FINISH ING MILL STAND WITH ROLLER、CHOCK & BEARIMG × 6SET: DIA∮ 300m m × 800m m L . 3.1. 8. FINISH ING MILL ROLLER × 3SET / 36pcs: DIA3 0 0 m m × 800m m L . 3.1.9. INLET & OUTLET GUIDE × 24SET: 3.1. 10. D C MOTO R × 2SET: 600HP×1SET、800HP×1SET. 3.1. 11 . A C MOTO R × 1SET: 800HP×1SET. 3.1.12. F LYING SHEAR FOR ROUGH MILL CUTTI NG HEAD: CUT FORCE MAX55mmSQ 3.1.13. F LYING SHEAR FOR INTERMEDI ATE MI LL CUTTING HEAD: CUT FORCE MAX35mmSQ 3.1.14. COLD SHEAR FOR LENTH CUTTING: CUT FORCE D32 × 12pcs(400TON) 3.1.15. 2HI PINION GEAR S TAND FOR FINISHING MILL:2set 3.1. 16. O T HER S PARE PA RT S 3.1.17. ASSEMBLING DR AW ING INCLUDE CIVIL FOUND ATION DW G. 、 MACHINE ASSEMBLING DW G. AND CABLE WIRING DW G. TOTAL EQUIPMENT WEIGHT: 1,731,700KG 4.1.1.CACULATION PLAN OF MILL CAPCITY ROLLING RATE (300,000T/Y) No. Products Billet Fin. Rolling Speed (m/sec) Pass Time (sec) Pause (sec) Rolling Cycle Time (sec) Product Yield (%) Annual Production Expected Rolling Hours (hrs) Size Area Unit-W Size Length Weight (%) (T/Year) (mm) (mm2) (kg/m) (mm) (m) (kg) 1 D10 78.5 0.617 130 6.0 796 11.7 110 10 5 15,000 2 D13 113.0 0.888 130 6.0 796 9.5 95 10 25 75,000 3 D16 176.7 1.387 150 6.0 1,060 7.71 95 10 20 60,000 4 D19 314.2 2.466 150 6.0 1,060 5.23 16.18 10 26.18 96 20 60,000 5 D22 380.1 2.984 150 6.0 1,060 5 15.6 10 25.6 96 5 15,000 6 D25 490.90 3.853 150 6.0 1,060 3.29 14.1 10 24.1 96 15 45,000 7 D32 804.25 5.313 150 6.0 1,060 3.29 14.1 10 24.1 96 8 24,000 8 D40 1,256 9.865 150 6.0 1,060 2.85 13 10 23 96 2 6,000 TOTAL 100 300,000 5,760 4.2.1 Product Mix and Rolling Rate II. DESIGN BASIS 2.1.1 Product Mix: Product mix for annual production of 300,000 tons is described as the table “Calculation Plan of Mill Capacity”. 2.1.2 Rolling Rate: With regard to rolling rate, please also refer to the table “Calculation Plan of Mill Capacity”. 2.1.3 Others: Product length of bars: 12M or others 4.2.2 Billet: Continuously cast billets or hot rolled billets Kind of steel: Low alloy steel for the manufacture of steel bars for reinforcement, rolled steel for general structure. Section 100 ～160mmSQ Length 6M ± 10 mm Weight 471～1206kg Camber (bow): Max.20mm in 6000mm length , Rhomboidity (right angularity): Less than 3% ,Twist: Less than 1 degree per meter Temperature of billet discharged: 1100℃～1200℃ (Engineering basis) Note: The billet above shall have the quality suitable for final products. In order to attain high productivity, that is, improvement of rolling efficiency and material yield, etc. which are resulted from high rolling Rate and most suitable cutting of Bar products , etc., it should be essential to well control the billet tolerance and conditions. 4.2.3 Rolling Capacity 4.2.3.1 Rolling Hours Required: Rolling Hours Requires=5760 Hrs/Year With regard to rolling hours required, please refer to the table to “Calculation Plan of Mill Capacity”. 4.2.3.2 Annual Working Hours:8 hours/shift×3 shift/day×300 day/year=7200Hr , If operating rate is 80% Operating Rate 0.8=Rolling hour required/Annual working hour , Rolling hour required=0.8×7200=5760Hr This operating ratio is considered to be easily attained. 4.2.4 Steel Grades: The steel grades which are to be processed on the mill are as follows. Deformed bar: D10~D40 Steel bar , Applicable standards: JIS 20-2525＆24-2536 “Rolled steel for general structure” Rung bar:∮10mm～∮40mm Steel bars JIS G 3101&JIS G4051 4.2.5 Rolling Speed: Actual rolling speed: Max. 11.7 m/sec 4.2.6 Rolling Method:1. Strand rolling , Deformed bars: D10～D40mm , Rung bars :∮ 10 mm～∮40mm 4.2.7 Site (Environmental) Conditions 1) Ambient temperature: Max. 35 deg. C (more than 15℃) , Electrical control room and pulpits will be kept in 20~30℃ 2) Relative humidity: Max. 98% 3) Altitude: Less than 1,000 m above sea level 1) Electric power Normal Electric power - Power receiving: One (1) line - Supplied power for 3set AC Motor: 3.3kv/3 phases /60HZ/2,000KW -Supplied power for 10set DC Motor: AC500v/3 phases /60/50HZ/5,600KW - Voltage fluctuation: Within ±5% - Frequency fluctuation: Terminals of 3.3kv receiving switch and distributing panel in the electrical equipment room of the plant. 2) Cooling water a. Direct Cooling Water (500 T/hr) b. Indirect Cooling Water (150 T/hr) pH valve: 6.5 to 8.5 6.5 to 8.5 Suspended solid: Max. 20 mg/lit Max. 10 mg/lit M-alkalinity as Ca Co3: Max. 300 mg/lit Max. 300 mg/lit Total dissolved solids: Max. 1,500 mg/lit Max. 1,500 mg/lit Total hardness as Ca Co3: Max. 300 mg/lit Max. 300 mg/lit Fe: Max. 3 mg/lit Max. 2 mg/lit Cl: Max. 200 mg/lit Max. 200 mg/lit So4: Max. 200 mg/lit Max. 200 mg/lit SiO2: Max. 50 mg/lit Max. 50 mg/lit Temperature: Max. 32℃ Max. 32℃ Pressure: Max. 4 kgf/cm2 Max. 4 kgf/cm2 Design pressure: 3 kgf/ cm2 at the battery Limit of the building 3 kgf/cm2 at the battery Limit of the building ITEM NO. EQUIPMENT NAME Q’TY SUPPLIER CUSTOMER REMARK Supply Country of origin Supply Country Weight KG M1 60TON/HR REHEATING FURNACE M101-01 Charging BED 6MtrW×4.5MtrL CHAIN TYPE 2 s ¡ TAIWAN 19,000 M101-02 Roller Way For Charging 1set ¡ TAIWAN 12,000 34MtrL M101-03 Hyd. Unit 1 s ¡ TAIWAN 3,000 M101-04 Main Pusher 2 s ¡ TAIWAN 21,200 M101-05 Furnace (Case8MtrW×22MtrL) 1 s ¡ TAIWAN 80,000 M101-06 Hot Wind Fuel Duct 1set ¡ TAIWAN 42,000 M101-07 Recuperate 1 s ¡ TAIWAN 20,000 M101-08 Chimney 1 p ¡ TAIWAN 36,000 40MtrH M101-09 Blower With AC Motor 100HP/4P/3∮/220V 1 s ¡ TAIWAN 3,600 590N m3/min M101-10 Burner (Heating Zoon:11set + Socking Zoon:5set) 16 s ¡ TAIWAN 6,400 M101-11 H/M Control Computer 1 s ¡ TAIWAN 100 M101-12 Auto Control Panel & MCC Panel For Furnace System 1 s ¡ TAIWAN 1,600 M101-13 Oil Valve, Oil Pump, Damper, Thermocouple, Oil Flow Meter 1 s ¡ TAIWAN 3,200 M101-14 Side Pusher 1 s ¡ TAIWAN 2,200 M101-15 Roller Way For Discharging 1 s ¡ TAIWAN 6,000 18M M101-16 Day Tank for Heavy Oil With Heater3set 1 s ¡ TAIWAN 3,500 M101-17 Refractory Bricks/Blocks 1Lot ---- ¡ M1. 60TON/HR REHEATING FURNACE TOTAL WEIGHT KG. 259,800 M2 MILL MECHANCAL SECTION M201 BREAKING DOWN MILL TRAIN ROLLER BEARING M201-01 Roller Way For Furnace To Roughing Mill 1 s ¡ TAIWAN 8,000 M201-02 Pusher For Billet Feed Back 1 s ¡ TAIWAN 2,500 M201-03 Horizontal 2HI-Mill Stand With Rest Bar 3 s ¡ JAPAN 19,500 M201-04 Mill Stand Base Plates 6 s ¡ JAPAN 3,000 M201-05 Roll(∮650mm×600mmL) (Assemble In Mill Stand) 6 s ¡ TAIWAN 10,800 M201-06 Chock (Assemble In Mill Stand) 12 s ¡ TAIWAN 4,800 M201-07 Roller Bearing (Assemble In Mill Stand) 12 s ¡ JAPAN 1,500 M201-08 K1 Reducer Gear Box With Pinion Gear 1 s ¡ JAPAN 14,000 i = 1/60.45 ITEM NO. EQUIPMENT NAME Q’TY SUPPLIER CUSTOMER REMARK Supply Country of origin Supply Country Weight KG M201-09 K2 Reducer Gear Box With Pinion Gear 1 s ¡ JAPAN 12,500 i = 1/45.14 M201-10 K3 Reducer Gear Box With Pinion Gear 1 s ¡ JAPAN 10,800 i = 1/33.65 M201-11 Gear Coupling (Motor - Reducer) 3 s ¡ JAPAN 2,100 M201-12 Cardan Shaft (Pinion Stand-Mill Stand) 3 s ¡ JAPAN 2,400 M201-13 Cardan Shaft Support 3 s ¡ JAPAN 1,800 M201-14 Inlet Guide Through 3 s ¡ TAIWAN 600 M201-15 Outlet Guide 2 s ¡ TAIWAN 400 M201-16 Outlet Guide & Twist Guide 1 s ¡ TAIWAN 300 M201-17 Oil Lubrication System 1 s ¡ JAPAN 3,500 M201-18 Roller Way For Roughing Mill To Intermediate Mill 1 s ¡ TAIWAN 10,000 M201-19 Hot Billet Shear 1 s ¡ JAPAN 7,500 M201 BREAKING DOWN MILL TRAIN TOTAL WEIGHT KG. 116,000 M202 ROUGHING MILL TRAIN FIBER BEARING TYPE M202-01 Horizontal 2HI-Mill Stand With Rest Bar 6 s ¡ JAPAN 36,000 M202-02 Mill Stand Base Plates 12 s ¡ JAPAN 8,400 M202-03 Roll(∮410mm×1,000mmL) (Assemble In Mill Stand) 12 s ¡ TAIWAN 18,000 M202-04 Chock (Assemble In Mill Stand) 24 s ¡ TAIWAN 400 M202-05 Fiber Bearing (Bakelite) (Assemble In Mill Stand) 24 s ¡ TAIWAN 100 M202-06 K4 & K5 Reducer Gear Box 1st 1 s ¡ JAPAN 7,200 i=1/28.37; M202-07 K4 & K5 Reducer Gear Box 2nd 1 s ¡ JAPAN 16,000 i=1/1.7; 1/1.2 M202-08 K6 & K7 Reducer Gear Box 1st 1 s ¡ JAPAN 6,500 i=1/17.476 M202-09 K6 & K7 Reducer Gear Box 2nd 1 s ¡ JAPAN 14,500 i=1/1.41; 1/1.14 M202-10 K8 & K9 Reducer Gear Box 1st 1 s ¡ JAPAN 5,400 i=1/4.29 M202-11 K8 & K9 Reducer Gear Box 2nd 1 s ¡ JAPAN 12,000 i=1/3.24; 12.28 M202-12 Pinion Gear Box 6 s ¡ JAPAN 21,000 M202-13 Gear Coupling (Motor - Reducer1st - Reducer2nd) 12 s ¡ JAPAN 2,400 M202-14 Join Shaft (Pinion Stand-Mill Stand) 12 s ¡ TAIWAN 4,800 M202-15 Join Coupling (Pinion Stand-Mill Stand) 24 s ¡ TAIWAN 3,600 M202-16 Inlet Guide Through 6 s ¡ TAIWAN 900 M202-17 Outlet Guide Plate Case 3 s ¡ TAIWAN 500 M202-18 Outlet Guide & Twist Guide 3 s ¡ TAIWAN 900 ITEM NO. EQUIPMENT NAME Q’TY SUPPLIER CUSTOMER REMARK Supply Country of origin Supply Country Weight KG M202-19 Oil Lubrication System 1 s ¡ JAPAN 4,000 M202-20 Roller Way For Roughing Mill To Intermediate Mill 1 s ¡ TAIWAN 18,000 M202 ROUGHING MILL TRAIN TOTAL WEIGHT KG. 180,600 M203 INTERMEDIATE MILL TRAIN ROLLER BEARING M203-01 Horizontal 2HI-Mill Stand With Rest Bar 6 s ¡ JAPAN 21,000 M203-02 Mill Stand Base Plates 12 s ¡ JAPAN 3,600 M203-03 Roll(∮300mm×800mmL) (Assemble In Mill Stand) 12 s ¡ TAIWAN 4,800 M203-04 Chock (Assemble In Mill Stand) 24 s ¡ TAIWAN 4,800 M203-05 Roller Bearing (4Rows+2Trust Load)(Assemble In Mill Stand) 24 s ¡ TAIWAN 2,400 M203-06 K10 & K11 Reducer Gear Box 1st 1 s ¡ JAPAN 9,000 i=1/5.39; M203-07 K10 Reducer Gear Box 2nd 1 s ¡ JAPAN 5,800 i=1/1.74; M203-08 K11 Reducer Gear Box 2nd 1 s ¡ JAPAN 4,500 i=1/1.316; M203-09 K12 & K13 Reducer Gear Box 1st 1 s ¡ JAPAN 8,500 i=1/5.39; M203-10 K12 Reducer Gear Box 2nd 1 s ¡ JAPAN 4,200 i=1/1.265; M203-11 K13 Reducer Gear Box 2nd 1 s ¡ JAPAN 4,000 i=1/1; M203-12 K14 & K15 Reducer Gear Box 1 s ¡ JAPAN 7,200 i=1/3.139; 1/2.583 M203-13 Connecting Shaft For Gear Box 2nd 2 s ¡ JAPAN 3,000 M203-14 Pinion Gear Box 6 s ¡ JAPAN 10,800 M203-15 Gear Coupling (Motor - Reducer1st - Reducer2nd) 16 s ¡ JAPAN 3,200 M203-16 Cardan Shaft (Pinion Stand-Mill Stand) 12 s ¡ TAIWAN 3,600 M203-17 Cardan Shaft Coupling (Pinion Stand-Mill Stand) 24 s ¡ TAIWAN 2,400 M203-18 Inlet Guide Through 6 s ¡ TAIWAN 600 M203-19 Outlet Guide Plate Case 3 s ¡ TAIWAN 200 M203-20 Outlet Guide & Twist Guide 3 s ¡ TAIWAN 600 M203-21 Oil Lubrication System 1 s ¡ JAPAN 3,000 M203-22 Roller Way For Intermediate Mill To Finishing Mill 4 s ¡ TAIWAN 28,000 2Strain M203 INTERMEDIATE MILL TRAIN TOTAL WEIGHT KG. 135,200 M204 FINISHING MILL TRAIN ROLLER BEARING TYPE M204-01 Horizontal 2HI-Mill Stand With Rest Bar 6 s ¡ JAPAN 21,000 M204-02 Mill Stand Base Plates 12 s ¡ JAPAN 3,600 ITEM NO. EQUIPMENT NAME Q’TY SUPPLIER CUSTOMER REMARK Supply Country of origin Supply Country Weight KG M204-03 Roll(∮290mm×800mmL) (Assemble In Mill Stand) 12 s ¡ TAIWAN 4,800 M204-04 Chock (Assemble In Mill Stand) 24 s ¡ TAIWAN 4,800 M204-05 Roller Bearing (4Rows+2Trust Load)(Assemble In Mill Stand) 24 s ¡ TAIWAN 2,400 M204-06 K16 & K17 Reducer Gear Box 1 s ¡ JAPAN 6,800 M204-07 K18 & K19 Reducer Gear Box 1 s ¡ JAPAN 6,500 M204-08 K20 Reducer Gear Box 1 s ¡ JAPAN 3,200 M204-09 K21 Reducer Gear Box 1 s ¡ JAPAN 3,000 M204-10 Pinion Gear Box 6 s ¡ JAPAN 10,800 M204-11 Gear Coupling (Motor - Reducer) 10 s ¡ JAPAN 2,000 M204-12 Cardan Shaft (Pinion Stand-Mill Stand) 12 s ¡ TAIWAN 3,600 M204-13 Cardan Shaft Coupling (Pinion Stand-Mill Stand) 24 s ¡ TAIWAN 2,400 M204-14 Inlet Guide Through 6 s ¡ TAIWAN 500 M204-15 Outlet Guide Plate Case 3 s ¡ TAIWAN 200 M204-16 Outlet Guide & Twist Guide 3 s ¡ TAIWAN 400 M204-17 Oil Lubrication System 1 s ¡ JAPAN 3,000 M204-18 Roller Way For Intermediate Mill To Finishing Mill 2 s ¡ TAIWAN 6,000 4Strain M204-19 Flying Shear For Rough Mill Cutting Head Max:SQ55mm 1 s ¡ JAPAN 4,500 M204-20 Flying Shear For Intermediate Mill Cutting Head Max:SQ35mm 1 s ¡ JAPAN 3,500 M204-21 Pinch Roller For Final Mill 4 s ¡ JAPAN 3,200 M204 FINISHING MILL TRAIN TOTAL WEIGHT KG. 96,200 M3 PRODUCT COLLECT PACKAGE MACHINE M301 COOLING BED EQUIPMENT 6MtrW×55MtrL M301-01 4 Strands Run In Frame With Kick Of 55MtrL/PICH 1Mtr 1 s ¡ TAIWAN 55,000 M301-02 Fixed Rakes 110 p ¡ TAIWAN 16,000 M301-03 Moving Rakes 110 p ¡ TAIWAN 18,000 M301-04 Fixed Frame 11 p ¡ TAIWAN 3,000 M301-05 Moving Frame With Cams Roller Guide 22 p ¡ TAIWAN 8,000 M301-06 Cams Shaft Group With Drive Equipment & Weights Frame 24 s ¡ TAIWAN 20,000 M301-07 Aligning Rollers With Reducer Gear Motor 80 s ¡ TAIWAN 3,200 M301-08 Raise Transport For Run Out With Cam Type Drive 55 s ¡ TAIWAN 24,000 ITEM NO. EQUIPMENT NAME Q’TY SUPPLIER CUSTOMER REMARK Supply Country of origin Supply Country Weight KG M301-09 Run Out Roller Table 58M/PICH 1Mtr 11 s ¡ TAIWAN 32,800 M301 COOLING BED EQUIPMENT TOTAL WEIGHT KG. 180,000 M302 LENGTH CUTTING & FINISHING SYSTEM M302-01 Cold Shear (Cut Force D32×12pcs 400Ton) 1 s ¡ JAPAN 22,000 M302-02 Length Cutting Device Max:24M/2Car 1 s ¡ JAPAN 35,000 M302-03 Roller Table 24MtrL/PICH 1MtrL 1 s ¡ TAIWAN 12,000 M302-04 Product Transfer(Type : Chain Traversing) 24MtrL 1 s ¡ TAIWAN 36,000 M302-05 Auto Binding Machine TYPE:ASV20 4 s ¡ JAPAN 10,200 DATON JAPAN M302-06 Transfer Roller Table 1 s ¡ JAPAN 18,200 TANAKA JAPAN M302-07 Auto Bundling Machine SUND BIRSTA KNSB 6/650 1 s ¡ SWIDEN 2,600 SUND SWIDEN M302-08 Product Transfer Roller Table 3 s ¡ TAIWAN 50,000 M302-09 Transportation Machine (Type : Chain Traversing) 1 s ¡ TAIWAN 21,000 M302-10 2 s ¡ TAIWAN 3,000 M302 LENGTH CUTTING & FINISHING SYSTEM EQUIPMENT TOTAL WEIGHT KG. 210,000 E1 POWER RECEIVING & DISTRIBUTION SYSTEM E101-01 DC Motors 600HP/600V/650～1,300rpm For Breaking Down 3 s ¡ TAIWAN 17,400 E101-02 DC Motors 600HP/600V/650～1,300rpm For Rough Mill 2 s ¡ TAIWAN 11,600 E101-03 DC Motors 800HP/600V/650～1,300rpm For Rough Mill 1 s ¡ TAIWAN 6,800 E101-04 AC Motors 800HP/3,300V/12P/580r.p.m For Intermediate 3 s ¡ TAIWAN 19,500 E101-05 DC Motors 600HP/600V/650～1,300rpm For Finishing Mill 1 s ¡ TAIWAN 5,800 E101-06 DC Motors 1,000HP/600V/650～1,300rpm For Finishing Mill 1 s ¡ TAIWAN 8,200 E101-07 DC Motors 800HP/600V/650～1,300rpm For Finishing Mill 2 s ¡ TAIWAN 13,600 E101-08 DC Motors 600HP On/Off Panel & Control Panel 3 s ¡ TAIWAN 1,800 E101-09 DC Motors 600HP On/Off Panel & Control Panel 2 s ¡ TAIWAN 1,200 E101-10 DC Motors 800HP On/Off Panel & Control Panel 1 s ¡ TAIWAN 600 E101-11 AC Motors 800HP On/Off Panel & Control Panel 3 s ¡ TAIWAN 1,800 E101-12 DC Motors 600HP On/Off Panel & Control Panel 1 s ¡ TAIWAN 600 E101-13 DC Motors 1,000HP On/Off Panel & Control Panel 1 s ¡ TAIWAN 600 E101-14 DC Motors 800HP On/Off Panel & Control Panel 2 s ¡ TAIWAN 1,200 ITEM NO. EQUIPMENT NAME Q’TY SUPPLIER CUSTOMER REMARK Supply Country of origin Supply Country Weight KG E101-15 11.4KV Electric Receive Equipment 5 s ¡ TAIWAN 3,000 E101-16 Transformer 2.0MVA/11.4KV-550V For Breaking Down 1 s ¡ TAIWAN 6,500 E101-17 Transformer 2.0MVA/11.4KV-550V For Rough Mill 1 s ¡ TAIWAN 6,500 E101-18 Transformer 2.5MVA/11.4KV-3,300V For Intermediate 1 s ¡ TAIWAN 7,800 E101-19 Transformer 3.0MVA/11.4KV-550V For Finishing Mill 1 s ¡ TAIWAN 8,500 E101-20 Transformer 1.0MVA/11.4KV-440V/220V/110V 1 s ¡ TAIWAN 5,200 E101-21 Operating Desk 4 s ¡ TAIWAN 400 E101-22 Auto Control Panel & MCC Panel For Furnace System 1 s ¡ TAIWAN 2,000 E101-23 Sensor Control-Photocell 1 s ¡ TAIWAN 200 E101-24 Auto Control Panel & MCC Panel For Product Collect Package 1 s ¡ TAIWAN 2,400 E101-25 MCC Panel For Public System 1 s ¡ TAIWAN 1,600 E101-26 H/M Control Computer 1 s ¡ TAIWAN 200 E1 POWER RECEIVING & DISTRIBUTION SYSTEM TOTAL WEIGHT KG. 135,000 P1 PUBLIC SYSTEM EQUIPMENT P101 AIR COMPRESSORS SYSTEM P101-01 150HP Compressors Screw Type FUSEN TAIWAN 3 s ¡ TAIWAN 6,000 NO.1#,8#,9# P101-02 60HP Compressors Screw Type FUSEN TAIWAN 4 s ¡ TAIWAN 4,800 NO.2#,3#,4#,5# P101-03 100HP Compressors Screw Type FUSEN TAIWAN 2 s ¡ TAIWAN 3,600 NO.6#,7# P101-04 Receiver Tank 3 s ¡ TAIWAN 4,800 P101-05 Refrigerated Air Dryer 3 s ¡ TAIWAN 1,800 P102 WATER SYSTEM PUMP P102-01 Indirect Water Pump 40HP/60HZ/3∮/220V 4 s ¡ TAIWAN 3,200 P102-02 Direct Water Pump 50HP/60HZ/3∮/220V 4 s ¡ TAIWAN 3,600 P102-03 Scale Water Outlet Pump 50HP/60HZ/3∮/220V 3 s ¡ TAIWAN 2,700 NO.MA,MB,MC P102-04 Scale Water Return Pump 50HP/60HZ/3∮/220V 2 s ¡ TAIWAN 1,800 NO.M43,M44 P102-05 Cooling Water Return Pump 25HP/60HZ/3∮/220V 5 s ¡ TAIWAN 2,000 M39,M40,M41,M42,M42A P102-06 Cooling Tower Pump 20HP/60HZ/3∮/220V 2 s ¡ TAIWAN 800 NO.M47,M48 P103 E.O.T. CRANE P103-01 A1. Span 18.925M / 7.5Ton E.O.T. Crane 1 s ¡ TAIWAN 14,000 P103-02 A2. Span 18.925M / 10Ton E.O.T. Crane 1 s ¡ TAIWAN 16,000 ITEM NO. EQUIPMENT NAME Q’TY SUPPLIER CUSTOMER REMARK Supply Country of origin Supply Country Weight KG P103-03 A3. Span 18.925M / 7.5Ton E.O.T. Crane 1 s ¡ TAIWAN 14,000 P103-04 B2、B3、B5 .Span 12.715M / 5Ton E.O.T. Crane 3 s ¡ TAIWAN 18,000 P103-05 B4、B6、Span 12.715M / 7.5Ton E.O.T. Crane 2 s ¡ TAIWAN 15,000 P103-06 C1 Span 14.695M / 5Ton E.O.T. Crane 1 s ¡ TAIWAN 5,500 P103-07 C2、C3、C4 Span 14.695M / 10Ton E.O.T. Crane 3 s ¡ TAIWAN 24,000 P1 PUBLIC SYSTEM EQUIPMENT TOTAL WEIGHT KG. 141,600 S1 SPARE PARTS EQUIPMENT S101-01 Spare Blower With AC Motor 100HP/4P/3∮/220V 1 s ¡ TAIWAN 3,600 590N m3/min S101-02 Spare Recuperate 1 s ¡ TAIWAN 20,000 S101-03 Spare Roller For Breaking Down Mill DIA∮650mm×600mmL 12 p ¡ TAIWAN 21,600 6pcs With Chock S101-04 Spare Roller For Rough Mill DIA∮410mm×1,000mmL 24 p ¡ TAIWAN 36,000 S101-05 Spare Fiber Bearing For Rough Mill 24 p ¡ TAIWAN 200 S101-06 Spare Stand With Roller & Chock For Intermediate Mill 6 s ¡ TAIWAN 30,000 S101-07 Spare Roller For Intermediate Mill DIA∮300mm×800mmL 24 p ¡ TAIWAN 12,000 12pcs With Chock S101-08 Spare Stand With Roller & Chock For Finishing Mill 6 s ¡ TAIWAN 30,000 S101-09 Spare Roller For Finishing Mill DIA∮300mm×800mmL 36 p ¡ TAIWAN 18,000 12pcs With Chock S101-10 Spare Inlet Guide、Outlet Guide Plate、Outlet Twist Guide 24 s ¡ TAIWAN 3,000 S101-11 Spare DC Motors 600HP/600V/650～1,300rpm 1 s ¡ TAIWAN 5,800 S101-12 Spare DC Motors 800HP/600V/650～1,300rpm 1 s ¡ TAIWAN 6,800 S101-13 Spare AC Motors 800HP/3,300V/12P/580r.p.m 1 s ¡ TAIWAN 6,500 S101-14 Spare Flying Shear For Rough Mill Max:SQ55mm 1 s ¡ JAPAN 4,500 S101-15 Spare Flying Shear For Intermediate Mill Max:SQ35mm 1 s ¡ JAPAN 3,500 S101-16 Spare Cold Shear (Cut Force D32×12pcs 400Ton) 1 s ¡ JAPAN 22,000 S101-17 Spare 2HI Pinion Gear Box 2 s ¡ JAPAN 3,600 S101-18 Other Spare Parts 1 s ¡ TAIWAN 50,000 S101-19 Assembling Drawing (Include : Civil Foundation DWG、Machine Assembling DWG. And Cable Wiring DWG.) 1 s ¡ TAIWAN 200 S1 SPARE PARTS EQUIPMENT TOTAL WEIGHT KG. 277,300 SUB. SUPPLY TOTAL WEIGHT KG. 1,731,700
二手電孤爐400,000T/Y USED STEEL MELT SHOP PLANT EQUIPMENT-161215-R
ITEM: USED 400,000TPY. STEEL MELT SHOP PLANT 1. GENERAL USED ELECTRAIC ARC FURNACE AND CCM SPECIFICATION Item Description Specification(60HZ AREA) Specification(50HZ AREA) 1 MATERIAL SCRAP: B1 80% + B2 20% + Vice Material( Mn, Si, Carbon) 2 ENERGY AC POWER 3 PRODUCT Billet: SQ□130mm×130mm×6〜12M CAP.:400,000TPY. Billet: SQ□130mm×130mm×6〜12M CAP.:320,000TPY. 4 TOTAL POWER 3∮AC161KV/ 48MW + 440V×3,000KW=51,000KW 3∮AC161KV/ 40MW + 440V×2,400KW=42,000KW 5 ARC FURNACE(768.6TON) 70TON-TAP ELECTRAIC ARC FURNACE TAP=50Min 70TON-TAP ELECTRAIC ARC FURNACE TAP=60Min TRANSFORMER:42,000KVA/3∮/60HZ TRANSFORMER:36,000KVA/3∮/50HZ ELECTRODE DIAMETER 22"∮/ 3 PHASE OXYGEN INJECTION SYSTEM 6 LADLE FURNACE(175TON) 50TON-TAP ELECTRAIC LADLE FURNACE TAP=50Min 50TON-TAP ELECTRAIC LADLE FURNACE TAP=60Min TRANSFORMER:10,000KVA TRANSFORMER:8,000KVA ELECTRODE DIAMETER 12"∮/ 3 PHASE AUTO VICE MATERIAL SYSTEM 7 DEDUSTING(385.9TON) BAG TYPE ARC FURNACE DEDUSSTING SYSTEM 8 CCM EQUIPMENT(718.4TON) 6 STRANDS CONTINUOUS CASTING MACHINE PRODUCT SPEED Max.: 5.4 M/Min COOLING BED: PLC Auto. W12M × L36M PRODUCT LENGTH: 6M～12M 9 200TPH. SCRAP SHREDDER SYSTEM(465.4TON) CAP.:200TON/HR, POWER:AC4500KW/6600V/60HZ CAP.:160TON/HR, POWER:AC3600KW/6600V/50HZ 10 OPERATING TYPE HMI SYSTEM PLC AUTO CONTROL 10 ONLINE OPERATOR 28Man×3Team ; Technician=8Man 11 FACTORY AREA HEAVY BUILDING WITH CRANE W25M×L180M×H30M×2+ W22M×L120M×H20M×2 =15,000M2 12 MANUFACTURER SHINKO JAPAN 13 DATE START 1989 ～ STOP FEB.2017 ※SUBTOTAL SUPPLY EQUIPMENT WEIGHT 2,513TON 1).70TON ELECTRAIC ARC FURNACE LIST OF EQUIPMENTS ×1set: SHINKO JAPAN BARCODE NO. EQUIPMENT NAME UNIT Q’TY UNIT W. TOTAL W. kg REMARK AF-M-01 ELECTRODE LIFTING SYSTEM 電極升降系統 AF-M-01-01 ELECTRODE LIFTING DRIVE MOTOR REDUCER set 3 3000 9,000 電極升降馬達減速機 AF-M-01-02 LIFTING GUIDE ROLLER set 6 600 3,600 升降導輪 AF-M-01-03 LIFTING SLIDING COLUMN set 3 2600 7,800 升降滑動柱 AF-M-01-04 CANTILEVER ELECTRODE set 3 3500 10,500 電極懸臂 AF-M-01-05 BRASS PIPE ELECTRODE set 6 1200 7,200 電極銅管 AF-M-01-06 ELECTRODE HOLDER DEVICE MAST set 3 600 1,800 電極把持器及桅杆頭 AF-M-02 ROOF LIFTING SYSTEM 爐蓋升降系統 AF-M-02-01 FURNACE ROOF set 1 15000 15,000 煉鋼爐蓋 AF-M-02-02 HANGING HOOK set 4 100 400 爐蓋吊具 AF-M-02-03 LIFTING CHAIN SPROCKET set 4 250 1,000 吊昇鍊條鍊輪 AF-M-02-04 HYDRAULIC CYLINDER set 2 500 1,000 油壓缸 AF-M-02-05 HYDRAULIC UNIT set 1 3000 3,000 AF-M-03 FURNACE SHELL BODY & WATER BOX 爐殼本體及冷卻水箱 AF-M-03-01 FURNACE TOP SHELL BODY OD6000mm∮×2800mmH set 1 52000 52,000 爐殼上部本體 AF-M-03-02 FURNACE BOTTOM SHELL BODY OD5890mm∮×2230mmH set 1 65000 65,000 爐殼下部本體 AF-M-03-03 FURNACE WALL WATER BOX set 1 4600 4,600 爐壁水箱 AF-M-03-04 BACK DOOR HEADSTOCK EQUIPMENT set 1 3000 3,000 爐後出鋼口爐門裝置 AF-M-03-05 FURNACE BACK DOOR FOR LIQUID STEEL set 1 2000 2,000 爐後出鋼口 AF-M-03-06 FURNACE FRONT CLEANER SLAG GATE set 1 3000 3,000 爐前除渣口 AF-M-03-07 FURNACE GATE WATER BOX set 1 1800 1,800 爐門水箱 AF-M-04 DUST SYSTEM 集塵系統 AF-M-04-01 DUST ELBOW set 1 3200 3,200 集塵灣頭 AF-M-04-02 DYNAMIC PIPE FOR HOT AIR DUST set 1 1500 1,500 熱氣摺動集塵管 AF-M-04-03 STARIGHT LEAD PIPE FOR COOL AIR DUST set 1 2300 2,300 冷風集塵直管 AF-M-04-04 BURNING TOWER set 1 13000 13,000 燃燒塔 AF-M-04-05 SUDDEN COOLING TOWER set 1 18500 18,500 驟冷塔 AF-M-04-06 GAS TOWER set 1 19500 19,500 瓦斯塔 AF-M-04-07 EXHAUST DUCT set 1 30000 30,000 風管 AF-M-05 VICE FEED MATERIAL BODIES UNDER SYSTEM 副料下料系統 AF-M-05-01 MATERIAL BODIES UNDER ROOF set 1 300 300 副料蓋 AF-M-05-02 MATERIAL BODIES UNDER AGENCY set 1 2750 2750 副料下料機構 AF-M-05-03 LARGE LIME BARREL set 1 9400 9400 大石灰桶 AF-M-05-04 SMALL LIME BUCKETS set 1 800 800 小石灰桶 AF-M-06 FURNACE ROOF CYCLE EQUIPMENT SYSTEM 爐蓋旋回裝置等 AF-M-06-01 CANTILEVER set 2 7800 15,600 懸臂 AF-M-06-02 CYCLE PLATFORM set 1 8000 8,000 旋迴平台 AF-M-06-03 CYCLE CENTRE BASE set 1 1000 1,000 旋迴中心樁 AF-M-06-04 CYCLE WHEEL set 2 1500 3,000 旋迴車輪 AF-M-06-05 CYCLE HYDRAULIC CYLINDER set 1 700 700 旋迴油壓缸 AF-M-06-06 CYCLE RAIL set 1 1100 1,100 旋迴軌道 AF-M-07 FURNACE SHELL BODY DUMPING SYSTEM 傾爐系統 AF-M-07-01 FURNACE SHELL BODY DUMPING PLATFORM set 1 36000 36,000 傾爐平台 AF-M-07-02 FURNACE DUMPING TOOTH ROW set 1 8600 8,600 傾爐齒排軌道 AF-M-07-03 FURNACE DUMPING DRIVE MOTOR REDUCER set 1 22000 22,000 傾爐傳動機構 AF-M-08 SCRAP IRON TRANSPORT SYSTEM 廢鐵轉運系統 AF-M-08-01 TRANSFER CAR AND RAIL set 1 12000 12,000 台車軌道機構 AF-M-08-02 SCRAP IRON DRESS BARREL set 5 22000 110,000 廢鐵桶 AF-M-08-03 SCRAP DRESS BARREL HANGER LOADING:70TON set 2 6000 12,000 廢鐵桶吊桿 AF-M-09 ASSISTED COMBUSTION SYSTEM 輔助燃燒系統 AF-M-09-01 COPPER WATER TANKS set 2 1200 2,400 銅水箱 AF-M-09-02 BURNER set 2 500 1,000 燃燒器 AF-M-09-03 LPG SYSTEM set 3 1600 4,800 液化瓦斯系統 AF-M-09-04 OXYGN INJECTION SYSTEM set 1 8500 8,500 氧氣噴射系統 AF-M-10 SURROUNDING ANCILLARY EQUIPMENT 周邊設備 AF-M-10-01 GUNNING MACHINE set 1 22000 22,000 補爐機 AF-M-10-02 CARBON INJECTING PURGE set 2 8500 17,000 增碳機 AF-E-01 ELECTRIC POWER SUPPLY SYSTEM 電力供應系統 AF-E-01-01 TRANSFORMER WITH OIL 42MVA/11.4KV-285V set 1 82000 82,000 變壓器 AF-E-01-02 11.4KV ELECTRIC RECEIVE EQUIPMENT set 1 4000 4,000 11.4KV電力受電設備 AF-E-01-03 TRANSFORMER WITH OIL 2MVA/11.4KV-440V/220V set 2 4500 9,000 其他設備用變壓器 AF-E-01-04 WATER COOLING INSULATED CABLES 9.5M/set set 6 2000 12,000 水冷絕緣電纜 AF-E-01-05 TRANSFORMER OUTLET COPPER PLATE set 1 4000 4,000 變壓器輸出銅板 AF-E-01-06 FURNACE MCC CONTROL PANEL set 1 6000 6,000 煉鋼爐開關控制盤 AF-E-01-07 FURNACE OPERATION CONTROL PANEL set 1 3000 3,000 煉鋼爐操作控制盤 AF-O-01 OTHER EQUIPMENT 其他設備 AF-O-01-01 70TON/SPAN19,190mm/15M CRANE FOR SCRAP set 1 NA 0 廢鐵廠天車 AF-O-01-02 70TON/SPAN19,190mm/15M CRANE FOR SCRAP set 1 NA 0 廢鐵廠天車 AF-O-01-03 30TON/SPAN19,190mm/15M CRANE FOR SCRAP 1 NA 0 廢鐵廠天車 AF-O-01-04 20TON/SPAN19,190mm/15M CRANE FOR VICE SYSTEM set 1 NA 0 副料廠天車 AF-O-01-05 30TON/ SPAN23,520mm/20M CRANE FOR FURNACE set 1 NA 0 煉鋼廠天車 AF-O-01-06 130+30TON/ SPAN23,520mm/20M CRANE FOR LADLE set 1 NA 0 煉鋼廠出鋼天車 AF-O-01-07 130+30TON/ SPAN23,520mm/20M CRANE FOR LADLE set 1 NA 0 煉鋼廠出鋼天車 AF-O-01-08 WATER PUMP AND PIPING FITTING set 1 14000 14,000 水泵浦 AF-O-01-09 HYDRAULIC UNIT set 1 6500 6,500 油壓泵浦單元 AF-O-01-10 2M3 HYDRAULIC SCRAP GRIPPER set 2 5000 10,000 油壓廢鐵夾 AF-O-01-11 DIA2500mm∮ELECTRIC MAGNETIC set 2 9000 18,000 電磁鐵 AF-O-01-10 COMPRESSED AIR STATION 12M3/min AC175HP set 3 3200 9,600 空氣壓縮機 AF-O-01-11 COMPRESSOR AIR REFRIGERATED DRYER set 1 1800 1,800 壓縮空氣乾燥機 AF-O-01-12 OTHER CABLE set 1 10000 10,000 其他電纜線 AF-D-01 EQUIPMENT INSTALLATION DRAWING 設備安裝圖 AF-D-01-01 Foundation & Anchor Bolt Elevation Azimuth Drawing set 基礎及螺絲位置高程圖 AF-D-01-02 Machinery Installation Group Legislative Drawing set 機械安裝組立圖 AF-D-01-03 Include Hydraulic, Air, water, Oil Lubrication Piping Drawing set 油壓空氣水循環油配管 AF-D-01-04 Include High Voltage & Low Voltage Cable Wiring Drawing set 高低壓配線圖 AF-D-01-05 Operations And Maintenance Manual set 操作維修手冊 AF-S-01 SPARE PARTS 備品 AF-S-01-01 ELECTRODE HOLDER DEVICE MAST set 1 電極把持器及桅杆頭 1). ARC FURNACE EQUIPMENT TOTAL WEIGHT(KG) 768,550 3). 6 STRANDS / 8M R USED CONTINUOUS CASTING MACHINE (CCM): BARCODE NO. EQUIPMENT NAME UNIT Q’TY UNIT W. TOTAL W. kg REMARK CCM CONTINUOUS CASTING MACHINE CCM-M-01-01 TUNDISH 6 HOLE set 18 5000 90,000 分流槽 CCM-M-01-02 LADLE 180。ROTATING MECHANISM set 1 35000 35,000 盛鋼桶旋轉台 CCM-M-01-03 ABNORMAL BYPASS set 2 2400 4,800 異常分流道 CCM-M-01-04 TUNDISH COVER set 1 1500 1,500 分流槽蓋 CCM -M-02-01 STEEL LIQUID VIBRATION AGENCY SYSTEM set 6 1200 7,200 鋼液震動設備 CCM -M-02-02 130mmSQ COPPER MOLD & WATER JACKET set 15 800 12,000 130mm銅模座 CCM -M-02-03 STEEL LIQUID VIBRATION DRIVE REDUCER set 6 1200 7,200 震動機驅動設備 CCM -M-03 SPRAY NOZZLE WITH PIPE 8M R set 6 800 4,800 不銹鋼噴水管 CCM -M-04 BILLET GUIDING APRON SYSTEM 8M R GUIDING set 6 2500 15,000 鋼胚導引設備 CCM -M-05-01 PINCH ROLLER BODY set 6 5500 33,000 夾送輥輪本體 CCM -M-05-02 PINCH ROLLER AGENCY SYSTEM set 6 3200 19,200 夾送輥輪機構 CCM -M-06 DELIVERY ROLLER WAY set 6 4500 27,000 傳送輥道 CCM -M-07-01 HYDRAULIC SHEAR BODY FORCE:250Ton set 6 9000 54,000 油壓剪 CCM -M-07-02 HYDRAULIC SHEAR AGENCY SYSTEM set 1 8000 8,000 油壓剪機構樑 CCM -M-08-01 HYDRAULIC PUMP UNIT FOR SHEAR & PINCH ROLLER set 6 4000 24,000 油壓單元 CCM -M-08-02 HYDRAULIC PIPING FOR SHEAR & PINCH ROLLER set 6 1500 9,000 油壓單元管路 CCM -M-09-01 PUSHER EQUIPMENT set 6 4000 24,000 推出設備 CCM -M-09-02 PUSHER EQUIPMENT AGENCY SYSTEM set 6 4000 24,000 推出設備機構 CCM -M-09-03 HYDRAULIC PUMP UNIT FOR PUSHER EQUIPMENT set 1 4000 4,000 推出油壓單元 CCM -M-10 OBLIQUE ROLLER TABLE set 1 4000 4,000 傾斜輥輪 CCM -M-11-01 LADLE BODY set 5 25000 125,000 盛鋼桶本體 CCM -M-11-02 LADLE COVER PLATE set 5 2000 10,000 盛鋼桶蓋板 CCM -M-11-03 LADLE GATE AGENCY SYSTEM set 4 400 1,600 盛鋼桶閥門機構 CCM -M-11-04 LADLE HANGER LOADING:150TON set 2 9800 19,600 盛鋼桶吊桿 CCM -M-12-01 COOLING WATER CONTROL VALVE SYSTEM set 6 600 3,600 冷卻水控制閥系統 CCM -M-13 PREHEATING EQUIPMENT FOR LADLE set 1 5000 5,000 盛鋼桶預熱設備 CCM -M-14 COPPER NOZZLE MOLD OIL INJECTION SYSTEM set 1 4000 4,000 鑄模噴油系統 CCM -M-15 COOLING BED FOR BILLET set 1 120000 120,000 鋼胚冷卻床 CCM -E-01 ELECTRICAL OPERATING EQUIPMENT set 1 1500 1,500 電力操作設備 CCM -E-02 ELECTRICAL CONTROL MCC PANEL set 1 2200 2,200 MCC控制盤 CCM -E-03 22.8KV ELECTRIC RECEIVE EQUIPMENT set 1 1000 1,000 電力受電設備 CCM -E-04 TRANSFORMER WITH OIL 2MVA/22.8KV-440V/220V/110 set 1 4500 4,500 CCM設備用變壓器 CCM -O-01 20TON/SPAN19,190mm/15M CRANE FOR CCM WORK ROOM set 1 NA 0 架空起重機 CCM -O-02 20TON/SPAN19,190mm/15M CRANE FOR CCM WORK ROOM set 1 NA 0 架空起重機 CCM -O-03 20TON/SPAN19,190mm/15M CRANE FOR CCM WORK ROOM set 1 NA 0 架空起重機 CCM -O-06 COMPRESSED AIR STATION 12M3/min AC100HP set 2 2600 5,200 空氣壓縮機 CCM -O-07 BILLET HANGER AGENCY SYSTEM set 1 7500 7,500 鋼胚吊架機構 CCM -D-01 EQUIPMENT INSTALLATION DRAWING set 1 設備安裝圖 3).C.C.M. EQUIPMENT TOTAL WEIGHT(KG) 718,400 4). ARC FURNACE DEDUSTING SYSTEM × 1set BARCODE NO. EQUIPMENT NAME UNIT Q’TY UNIT W. TOTAL W. kg REMARK DC-M-01 EXHAUST DUCT 廢氣煙道 DC-M-01-01 ROOF DUST COVER set NA 0 屋頂集塵罩 DC-M-01-02 SIDE WALL DUST COVER set 1 12,000 12,000 側牆集塵罩 DC-M-01-03 EXHAUST DUCT 150M×1set set 1 120,000 120,000 廢氣煙道 DC-M-01-04 SUPORT FOR EXHAUST DUCT set 1 40,000 40,000 廢氣煙道支撐架 DC-M-02 DUST COLLECTION CASING 0 集塵外殼 DC-M-02-01 FURNACE MOUTH DEDUSTING CASING set 1 150,000 150,000 爐嘴廢氣集塵室 DC-M-02-02 ROOF AND SIDE WALL DEDUSTING CASING set NA 0 屋頂及側牆集塵室 DC-M-03 OUTSIDE THE FRAMEWORK OF THE BAG 濾袋鐵線框 DC-M-03-01 FRAME FOR FURNACE MOUTH DUST pcs 1200 3 3,600 爐嘴鐵線框 DC-M-03-02 FRAME FOR ROOF AND SIDE WALL DUST pcs NA 0 屋頂及側牆鐵線框 DC-M-04 AIR BAG 濾袋 DC-M-04-01 BAG FOR FURNACE MOUTH DUST pcs 1200 3 3,600 爐嘴濾袋 DC-M-04-02 BAG FOR ROOF AND SIDE WALL DUST pcs NA 0 屋頂及側牆濾袋 DC-M-05 GATE BAFFLE FILTER ROOM 過濾室閥門檔板 DC-M-05-01 GATE BAFFLE FOR FURNACE MOUTH DUST set 12 150 1,800 爐嘴過濾室閥門 DC-M-05-02 GATE BAFFLE FOR ROOF AND SIDE WALL DUST set NA 0 屋頂及側牆過濾室閥門 DC-M-05-03 AIR CYLINDER set 30 20 600 氣壓缸 DC-M-06 AIR SOLENOID GATE VALAE EQUIPMENT 氣壓控制閘閥設備 DC-M-06-01 AIR RECEIVER TANK WITH SOLENOID GATE set 15 200 3,000 氣壓儲存桶附閘閥 DC-M-07 LEAF BLOWER DC-M-07-01 LEAF BLOWER FOR FURNACE MOUTH DUST set 1 12,000 12,000 爐嘴鼓風機 DC-M-07-02 LEAF BLOWER FOR ROOF AND SIDE WALL DUST set NA 0 屋頂及側牆鼓風機 DC-M-08 DUCT CONVEYOR EQUIPMENT 粉塵輸送設備 DC-M-08-01 DUCT CONVEYOR FOR FURNACE MOUTH DUST set 1 3,000 3,000 爐嘴粉塵輸送 DC-M-08-02 DUCT CONVEYOR FOR ROOF AND SIDE WALL DUST set NA 0 屋頂及側牆粉塵輸送 DC-M-08-03 AIR CYLINDER set 10 20 200 氣壓缸 DC-M-09 COMPRESSOR AIR STATION 20M3/min 0 壓縮空氣站 DC-M-09-01 AIR COMPRESSOR AC175HP set 2 3,600 7,200 空氣壓縮機 DC-M-09-02 COMPRESSOR AIR TANK set 1 3,000 3,000 壓縮空氣桶 DC-M-09-03 COMPRESSOR AIR REFRIGERATED DRYER set 1 1,500 1,500 冷凍乾燥機 DC-E-01 ELECTRIC EQUIPMENT 0 電氣設備 DC-E-01-01 800HP MOTOR FOR FURNACE MOUTH DUST BLOWER set 1 6,800 6,800 爐嘴鼓風機馬達 DC-E-01-02 1,200HP FOR ROOF AND SIDE WALL DUST BLOWER set NA 0 屋頂及側牆鼓風機馬達 DC-E-01-03 TRANSFORMER WITH OIL 1.5MVA/11.4KV-660V set NA 0 2,500KVA變壓器 DC-E-01-04 TRANSFORMER WITH OIL 1.25MVA/11.4KV-3300V/220V set 1 3,600 3,600 1,500KVA變壓器 DC-E-01-06 MCC & OPERATION CONTROL PANEL set 2 1,500 3,000 操作控制盤 DC-E-01-07 11.4 KV ELECTRIC RECEIVE EQUIPMENT set 1 1,000 1,000 11.4KV電力受電設備 DC-E-01-08 OTHER CABLE set 1 10,000 10,000 其他電纜線 DC-D-01 EQUIPMENT INSTALLATION DRAWING set 1 0 0 設備安裝圖 4). DEDUSTING EQUIPMENT TOTAL WEIGHT(KG) 385,900 5). 200TPH. SCRAP SHREDDER EQUIPMENT SYSTEM × 1set BARCODE NO. EQUIPMENT NAME UNIT Q’TY UNIT W. TOTAL W. kg REMARK M-01 CONVEYOR (PLATE TYPE W2400mm) HYD. MOTOR SET 1 12,000 12,000 輸送帶 M-02 HYDRAULIC UNIT 90KW SET 1 4,000 4,000 油壓單元 M-03 ROLLER FOR INLET MATERIAL SET 1 6,000 6,000 進料滾輪 M-04 HYDRAULIC UNIT 110KW SET 1 5,000 5,000 油壓單元 M-05 SHREDDER BODY SET 1 240,000 240,000 粉碎主機 M-06 MOTOR 4500KW/6600V/450rpm. SET 1 22,000 22,000 馬達 M-07 UNIVERSAL JOINT SET 2 800 1,600 萬向傳動軸 M-08 VIBRAITING CONVEYOR W1710mm/15KW/440V/6Cycle/Sec SET 1 4,000 4,000 震動輸送帶 M-09 DEDUSTING EQUIPMENT SET 1 30,000 30,000 集塵器 M-10 CONVEYOR (BLETS TYPE W1400mm/L20m)18.5KW SET 1 10,000 10,000 輸送帶 M-11 VIBRAITING CONVEYOR W2300mm/5.5KW/440V/6Cycle/Sec SET 1 4,000 4,000 震動輸送帶 M-12 ROTARY MAGNETIC SEPARATOR W2400mm 11KW+13.2KW SET 1 8,000 8,000 磁選機設備 M-13 CONVEYOR (BLETS TYPE W1200mm*L21m)15kw SET 1 10,000 10,000 輸送帶 M-14 ASR CONVEYOR (BLETS TYPE W1050mm*L8m)5.5KW SET 1 4,000 4,000 輸送帶 M-15 CONVEYOR (BLETS TYPE W1050mm*L5m)5.5KW SET 1 3,000 3,000 輸送帶 M-16 CONVEYOR (BLETS TYPE W1050mm*L10m)5.5KW SET 1 5,000 5,000 輸送帶 M-17 VIBRAITING MACHINE W1100mm/2KW/6Cycle/Sec SET 1 1,500 1,500 輸送帶 M-18 CONVEYOR (BLETS TYPE W1050mm*L10m)5.5KW SET 1 5,000 5,000 輸送帶 M-19 MAGNETIC SEPARATOR W800mm 3KW+3.1KW SET 1 3,000 3,000 輸送帶 M-20 CONVEYOR (BLETS TYPE W1200mm*L20m)15kw SET 1 10,000 10,000 輸送帶 M-21 CONVEYOR (BLETS TYPE W1200mm*L17m)15kw SET 1 9,000 9,000 輸送帶 M-22 CONVEYOR (BLETS TYPE W1200mm*L20m)15kw SET 1 10,000 10,000 輸送帶 M-23 CONVEYOR (BLETS TYPE W1200mm*L10.5m)15kw SET 1 5,000 5,000 輸送帶 M-24 CONVEYOR (BLETS TYPE W1200mm*L17m)15kw SET 1 9,000 9,000 輸送帶 M-25 CONVEYOR (BLETS TYPE W1050mm*L9.5m)5.5KW SET 1 5,000 5,000 輸送帶 M-26 CONVEYOR (BLETS TYPE W1200mm*L17m)15kw SET 1 9,000 9,000 輸送帶 M-27 CONVEYOR (BLETS TYPE W1200mm*L14m)15kw SET 1 6,000 6,000 輸送帶 M-28 CONVEYOR (BLETS TYPE W1200mm*L14m)15kw SET 1 6,000 6,000 輸送帶 M-29 CONVEYOR (BLETS TYPE W1050mm*L9m)5.5KW SET 1 4,000 4,000 輸送帶 M-30 TRANSFORMER WITH OIL 7.5MVA/11.4KV-6.6KV SET 1 12,300 12,300 M-31 CONTROL PANEL SET 1 2,000 2,000 5). 200TPH. SCRAP SHREDDER MACHINE TOTAL WEIGHT(KG) 465,400 BARCODE NO. EQUIPMENT NAME Q’TY UNIT kg WHIGHT kg RM1M101-01 Charging BED 1 8,000 8,000 RM1M101-02 Roller Way For Charging 1 12,000 12,000 RM1M101-03 Hyd. Unit 1 3,000 3,000 RM1M101-04 Main Pusher 2 11,000 22,000 RM1M101-05 Furnace (Case8MtrW×22MtrL) 1 80,000 80,000 RM1M101-06 Hot Wind Fuel Duct 1 42,000 42,000 RM1M101-07 Recuperate 1 20,000 20,000 RM1M101-08 Chimney 1 36,000 36,000 RM1M101-09 Blower With AC Motor 100HP/4P/3∮/220V 1 3,600 3,600 RM1M101-10 Burner (Heating Zoon:4set + Socking Zoon:2set) 6 500 3,000 RM1M101-11 H/M Control Computer 1 1000 1,000 RM1M101-12 Auto Control Panel & MCC Panel For Furnace System 1 1,600 1,600 RM1M101-13 Oil Valve, Oil Pump, Damper, Thermocouple, Oil Flow Meter 1 3,200 3,200 RM1M101-14 Side Pusher 1 4,000 4,000 RM1M101-15 Roller Way For Discharging 1 6,000 6,000 RM1M101-16 Day Tank for Heavy Oil 1 3,500 3,500 RM1M101-17 Refractory Bricks/Blocks 1 0 0 RM1-M1 PREHEATING FURNACE SUBTOTAL 248,900 RM1-M2 MILL MECHANCAL SECTION RM1-M201 ROUGHING MILL TRAIN ROLLER BEARING TYPE RM1M201-01 Horizontal 2HI-Roughing Mill Stand With Rest Bar 4 8,540 34,160 RM1M201-02 Mill Stand Base Frame 4 7,050 28,200 RM1M201-03 Roll(∮500mm×800mmL) (Assemble In Mill Stand) 8 1,500 12,000 RM1M201-04 Chock (Assemble In Mill Stand) 16 300 4,800 RM1M201-05 Roller Bearing (Assemble In Mill Stand) 16 100 1,600 RM1M201-06 Vertical 2HI-Roughing Mill Stand With Rest Bar 3 8,540 25,620 RM1M201-07 Mill Stand Base Frame 3 13,400 40,200 RM1M201-08 Roll(∮500mm×800mmL) (Assemble In Mill Stand) 6 1,500 9,000 RM1M201-09 Chock (Assemble In Mill Stand) 12 300 3,600 RM1M201-10 Roller Bearing (Assemble In Mill Stand) 12 100 1,200 RM1M201-11 K1 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 12,700 12,700 RM1M201-12 K2 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 12,700 12,700 RM1M201-13 K3 Reducer Gear Box With Pinion Gear Vertical 2HI 1 18,340 18,340 RM1M201-14 K4 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 12,700 12,700 RM1M201-15 K5 Reducer Gear Box With Pinion Gear Vertical 2HI 1 12,370 12,370 RM1M201-16 K6 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 9,610 9,610 RM1M201-17 K7 Reducer Gear Box With Pinion Gear Vertical 2HI 1 11,200 11,200 RM1M201-18 Gear Coupling (Motor - Reducer) 7 400 2,800 RM1M201-19 Cardon Shaft With Coupling (Pinion Stand-Mill Stand) 14 1,320 18,480 RM1M201-20 Inlet Guide 7 300 2,100 RM1M201-21 Outlet Guide 7 450 3,150 RM1M201-22 Oil Lubrication System-No.1 1 7,500 7,500 RM1M201-23 Roller Way For Roughing Mill To Intermediate Mill 6M 1 4,600 4,600 RM1-M201 ROUGHING MILL TRAIN SUBTOTAL 288,630 RM1-M202 INTERMEDIATE MILL TRAIN ROLLER BEARING TYPE RM1M202-01 2Hi Horizontal -Intermediate Mill Stand With Rest Bar 2 4,800 9,600 RM1M202-02 Mill Stand Base Frame 2 1,900 3,800 RM1M202-03 Roll ∮420 × 800L(Assemble In Mill Stand) 4 1,050 4,200 RM1M202-04 Chock(Assemble In Mill Stand) 8 240 1,920 RM1M202-05 Roller Bearing(4Rows+2Trust Load) (Assemble In Mill Stand) 8 100 800 RM1M202-06 2HI Vertical-Intermediate Mill Stand With Rest Bar 2 4,800 9,600 RM1M202-07 Mill Stand Base Frame 2 7,500 15,000 RM1M202-08 Roll ∮420 × 800L(Assemble In Mill Stand) 4 1,050 4,200 RM1M202-09 Chock(Assemble In Mill Stand) 8 240 1,920 RM1M202-10 Roller Bearing(4Rows+2Trust Load) (Assemble In Mill Stand) 8 100 800 RM1M202-11 K8 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 9,550 9,550 RM1M202-12 K9 Reducer Gear Box With Pinion Gear Vertical 2HI 1 12,000 12,000 RM1M202-13 K10 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 9,550 9,550 RM1M202-14 K11 Reducer Gear Box With Pinion Gear Vertical 2HI 1 12,000 12,000 RM1M202-15 Gear Coupling (Motor-Reducer Gear) 4 320 1,280 RM1M202-16 Cardon Shaft (Reducer-Mill Stand) 8 1,200 9,600 RM1M202-17 Inlet Guide 4 125 500 RM1M202-18 Outlet Guide & Twist Guide 4 150 600 RM1-M202 INTERMEDIATE MILL TRAIN SUBTOTAL 106,920 RM1-M203 FINISHING MILL TRAIN ROLLER BEARING TYPE RM1M203-01 2Hi Horizontal -Finishing Mill Stand With Rest Bar 5 4,600 23,000 RM1M203-02 Mill Stand Base Frame 5 1,900 9,500 RM1M203-03 Roll ∮360 × 600L(Assemble In Mill Stand) 10 800 8,000 RM1M203-04 Chock(Assemble In Mill Stand) 20 200 4,000 RM1M203-05 Roller Bearing(4Rows+2Trust Load) (Assemble In Mill Stand) 20 100 2,000 RM1M203-06 2Hi Vertical -Finishing Mill Stand With Rest Bar 1 4,600 4,600 RM1M203-07 Mill Stand Base Frame 1 6,500 6,500 RM1M203-08 Roll ∮360 × 600L(Assemble In Mill Stand) 2 800 1,600 RM1M203-09 Chock(Assemble In Mill Stand) 4 200 800 RM1M203-10 Roller Bearing(4Rows+2Trust Load) (Assemble In Mill Stand) 4 100 400 RM1M203-11 K12 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 3,800 3,800 RM1M203-12 K13 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 3,800 3,800 RM1M203-13 K14 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 3,800 3,800 RM1M203-14 K15 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 3,800 3,800 RM1M203-15 K16 Reducer Gear Box With Pinion Gear Horizontal 2HI 1 3,800 3,800 RM1M203-16 K17 Reducer Gear Box With Pinion Gear Vertical 2HI 1 7,200 7,200 RM1M203-17 Gear Coupling (Motor-Reducer Gear- Pinion Stand) 6 300 1,800 RM1M203-18 Cardon Shaft (Pinion Stand -Mill Stand) 12 1,080 12,960 RM1M203-19 Inlet Guide 6 100 600 RM1M203-20 Outlet Guide & Twist Guide 6 120 720 RM1M203-21 Down Looper System 4 1,350 5,400 RM1M203-22 Oil Lubrication System-No.2 1 6,500 6,500 RM1M203-23 Roller Way For Finishing Mill To Cooling Bed 36M 1 16,000 16,000 RM1-M203 FINISHING MILL TRAIN SUBTOTAL 130,580 RM1-M204 SHEAR MACHINE RM1M204-01 No.1 Flying Shear Power:AC37KW/6P Max:□SQ55mm 1 18,500 18,500 RM1M204-02 No.2 Flying Shear Power:AC22KW/6P Max:□SQ35mm 1 14,000 14,000 RM1M204-03 No.3 Flying Shear AC 7.5HP*4P*2 ; Cut Force:D10～D29 2 3,600 7,200 RM1M204-04 Cold Shear (Force:400Ton D32*15pcs) AC100HP/6P 1 23,500 23,500 RM1-M204 SHEAR MACHINE SUBTOTAL 63,200 RM1-M3 COOLING BED AND CUTTING SECTION RM1-M301 11 Mtr W×70MtrL COOLING BED RM1M301-01 Run in Guiding Through (70M) 1 18,000 18,000 RM1M301-02 Separator () With Stop Brake 1 1,600 1,600 RM1M301-03 Kick Off Device 1 2,400 2,400 RM1M301-04 Rack Working Cooling Bed 70M Length With Cam Type Drive 1 160,000 160,000 RM1M301-05 Moving Frame Drive Unit AC MOTOR 75HP/6P 2 12,600 25,200 RM1M301-06 Bar Collecting Device 1 4,800 4,800 RM1M301-07 Aligning Rollers 1 3,500 3,500 RM1M301-08 Raise Transport For Run Out With Cam Type Drive 1 9,600 9,600 RM1M301-09 Run Out Roller Table 70M 1 36,000 36,000 RM1M301-10 Cold Shear Run Out Table 32M 1 21,000 21,000 RM1M301-11 Product Transfer 1 40,000 40,000 RM1M301-12 Shipping Table 1 56,000 56,000 RM1M301-13 Hyd. Unit 1 5,600 5,600 RM1M301-14 Bundling Frame 15M 1 15,600 15,600 RM1-M3 COOLING BED AND CUTTING SECTION SUBTOTAL 399,300 RM1-E1 POWER RECEIVING & DISTRIBUTION SYSTEM RM1E101-01 DC Motors 350KW/600V/600〜1,200r.p.m 7 4,500 31,500 RM1E101-02 DC Motors 350KW/600V/600〜1,200r.p.m 10 6,500 65,000 RM1E101-03 DC Motors 350KW On/Off Panel & Control Panel 7 1,000 7,000 RM1E101-04 DC Motors 450KW On/Off Panel & Control Panel 10 1,200 12,000 RM1E101-05 11.4KV Electric Receive Equipment 1 1,000 1,000 RM1E101-06 Transformer With Oil 1.5MVA/11.4KV-440v/220V 1 4,000 4,000 RM1E101-07 Transformer With Oil 2.5MVA/11.4KV-550V For DC Motor 3 4,500 13,500 RM1E101-08 HMI. System Operating Desk 4 400 1,600 RM1E101-09 Auto Contral Panel & MCC Panel For Furnace 1 2,500 2,500 RM1E101-10 Auto Contral Panel & MCC Panel For Mill Line 1 2,500 2,500 RM1E101-11 Auto Contral Panel & MCC Panel For Colling Bed & Cutting Line 1 3,000 3,000 RM1E101-12 Sensor Control-Photocell 8 100 800 RM1-E POWER RECEIVING & DISTRIBUTION SYSTEM SUBTOTAL 282,500 RM1-O1 PUBLIC SYSTEM EQUIPMENT RM1O401-01 Air Compressed 150HP 2 2,200 4400 RM1O401-02 Compressed Air Dry Equipment 1 800 800 RM1O401-03 Air Receiver Tank 3 800 2400 RM1O401-04 Water Pump 50Hp / 10〞Outlet 2 1,200 2400 RM1O401-05 Water Pump 40Hp / 8〞Outlet 2 900 1800 RM1-O1 PUBLIC SYSTEM EQUIPMENT SUBTOTAL 11,800 RM1-S1 MILL STAND SPARE PARTS RM1S1-01 2Hi Horizontal Rough Mill Stand With Roller & Chock 4 8,540 34,160 RM1S1-02 2Hi Vertical Rough Mill Stand With Roller & Chock 3 8,540 25,620 RM1S1-03 2Hi Horizontal Intermediate Mill Stand With Roller & Chock 2 4,800 9,600 RM1S1-04 2Hi Vertical Intermediate Mill Stand With Roller & Chock 2 4,800 9,600 RM1S1-05 2Hi Horizontal Finishing Mill Stand With Roller & Chock 5 4,600 23,000 RM1S1-06 2Hi Vertical Finishing Mill Stand With Roller & Chock 1 4,600 4,600 RM1S1-07 DC Motor 350KW 2 100 200 RM1S1-08 DC Motor 450KW 1 7,600 7,600 RM1S1-09 Roll(∮500mm×800mmL)For Rough Mill 14 1,570 21,980 RM1S1-10 Roll(∮420mm×800mmL)For Intermediate Mill 8 700 5,600 RM1S1-11 Roll(∮360mm×600mmL)For Finishing Mill 12 700 8,400 RM1S1-12 Chock With Roller Bearing For Rough Mill 14 400 5,600 RM1S1-13 Chock With Roller Bearing For Intermediate Mill 8 340 2,720 RM1S1-14 Chock With Roller Bearing For Finishing Mill 12 300 3,600 RM1S1-15 Cardon Shaft For Roughing Mill 1 1,320 1,320 RM1S1-16 Cardon Shaft For Intermediate Mill 1 1,200 1,200 RM1S1-17 Cardon Shaft For Finishing Mill 1 1,080 1,080 RM1S1-18 Inlet Guide For Roughing Mill 7 300 2,100 RM1S1-19 Outlet And Twist Guide For Rough Mill 7 450 3,150 RM1S1-20 Inlet Guide For Intermediate Mill 4 125 500 RM1S1-21 Outlet And Twist Guide For Intermediate Mill 4 150 600 RM1S1-22 Inlet Guide For Finishing Mill 6 100 600 RM1S1-23 Outlet And Twist Guide For Finishing Mill 6 125 750 RM1S1-24 Blade For Flying Shear 4 10 40 RM1S1-25 Blade For Cold Shear 4 50 200 RM1S1-26 Flying Shear Power:AC37KW/6P Max:□SQ55mm 1 18,500 18,500 RM1S1-27 AC Motor 2HP ～100HP For Other 1 20,000 20,000 RM1S1-28 Other Spare Parts 1 20,000 20,000 RM1S1 MILL STAND SPARE PARTS SUBTOTAL 232,320 RM1D DRAWING RM1D1-01 Rolling Pass Schedule & K1～K17 Groove Division 1 0 RM1D1-02 Foundation & Anchor Bolt Elevation Azimuth Drawing 1 0 RM1D1-03 Machinery Installation Group Legislative Drawing 1 0 RM1D1-04 Include Hydraulic, Air, water, Oil Lubrication Piping Drawing 1 0 RM1D1-05 Include High Voltage & Low Voltage Cable Wiring Drawing 1 0 RM1D1-06 Operations And Maintenance Manual 1 0 RM1D DRAWING SUBTOTAL 0 5). RM1 : D12mm～D38mm BAR ROLLING MILL 17PASS TOTAL 1,764,150 BARCODE NO. EQUIPMENT NAME Q’TY UNIT kg WHIGHT kg
二手軋鋼日本型鋼筋和圓棒軋鋼設備 Mill-1061129 Used Japan made Mill for Rebar and Round Bar
二手軋鋼日本型鋼筋和圓棒軋鋼設備 Mill-1061129 Used Japan made Mill for Rebar and Round Bar
二手電磁鐵和捲線器-98015
Used & New Magnet System Project : 98015 Detail specification of used & New magnet system and CONTENT 1. Detail Specification of Used Magnet System , Quantity and We........2~3 2. Phot......................................................................................................4~12 3. Brochures of Used Magnets...................................................................13~19 4. S. Walker Catalogue............................................................................20~21 Detail Specification of Used Magnet System and Weight Item No. Specification Qty. Weight/Unit (KGS) Total/WT (KGS) Remark 1 (a) Used Walker magnet to handle billet 130mm x 130mm x 12m x 9~10pcs , 1.6T/pc x 10pcs = 16T Magnet Grabber model No. 29” x 52” , 230VDC , 32.8A , 75% duty cycle in very good condition 2EA + 1spare 3090 9270 (b) Spread beam (used) capacity : 12,750kg , 2 lifting lug in distance 3M , total beam length : 5M 1EA 1000 1000 (c) New control system and BBUS without batteries For 2EA magnets to handle billets Grabber model # 29” x 52” , 32.8A/EA , total : 64A , 3phase full bridge rectifier , capacity : 15KW , with battery charger (floating & equalizing) for battery back up system recommend battery 120AH , lead acid battery 12V x 19pcs = 228V , input : 380V-3phase-50HZ 1EA 150 150 (c-1) Used Walker control & transformer , type 4791 , M/L 91819-103 , cold amp : 430 , 480V-3-60HZ input 250VDC out put, not included. Battery enclosure. It need to take time to estimate the revamping cost . 1EA 180 180 2 Used rebar bundle handling magnet system (a) Rebar length up to 12m , magnet model Grabber # 24” x 52” , max. bundle dia. : 400mm , 230VDC , magnet 19.48A , 75%ED , total layer width : 1200mm , max. capacity : 3T x 3bundles = 9 TON 10EA + 2spare 2000 24000 (b) Fixed beam in capacity : 12,750kg , total length : 13.5M , weight : 3.2T , 2 lifting distance : 3M 2EA 3000 6000 (c) New controller and battery back up system without battery For 5EA magnet system to handle the rebar bundles Walker’s model # Grabber 24” x 52” , 20A/EA x 5pcs , magnet = 100A in total , 3phase full bridge rectifier , capacity : 25KW , with battery charger (floating & equalizing) for battery back up system recommend battery 120AH , lead acid battery 12V x 19pcs = 228V , input : 380V-3phase-50HZ 2EA 200 400 (c-1) Used Walker control & transformer , type 4791 , M/L 91819-103 , cold amp : 430 , 480V-3-60HZ input 250VDC out put, not included. Battery enclosure. It need to take time to estimate the revamping cost . 2EA 230 460 3 (a) Used Sumitomo circular magnet LECK 15A 7 Sumitomo , Magnet : dia. 1.5m , deep field , 59A , 230VDC 1EA 3200 3200 (b) Controller new without BBUS 1EA 100 100 4 Used Walker circular magnet (a) 93” SD , , 230VDC x 180A 1EA 7500 7500 (b) Controller new without BBUS 1EA 120 120 5 NEW 1.65M SMW1 circular magnets for scrap handling Model # SMW1-16CA , dia. : 1650mm , 220VDC , current : 61.5A , power : 13.5KW 1EA 2600 2600 6 MMD Cable reel MMD281002-320-13-1 for AWG 1 (43mm²) x 3C , capacity of slip ring : 200A , 50FT type W cable 3EA 170 540 54,880 Less 1(c-1) & 2(c-1)
