3-15.齒輪型剎車鼓連軸器GEARED BRAKE WHEEL COUPLINGS-01 點擊圖片放大
商品名稱:

3-15.齒輪型剎車鼓連軸器GEARED BRAKE WHEEL COUPLINGS-01

詳細介紹:

3. 鼓式剎車HI-TORK DRUM BRAKE                                                                             下載down load3. 鼓式剎車HI-TORK DRUM BRAKE  
      3-2.內容和頁數導引說明CONTENTS AND PAGE REFERENCE GUIDE
    3-3.介紹說明INTRODUCTION
    3-4.介紹說明INTRODUCTION 
      3-5.DC磁鐵操作剎車DC MAGNET OPERATED BRAKES 
      3-6.DC磁鐵操作剎車DC MAGNET OPERATED BRAKES
      3-7.3相AC油壓致動器剎車
             3 PHASE AC HY-THRUST TM ACTUATOR BRAKES
      3-8.3相AC油壓致動器剎車
             3 PHASE AC HY-THRUST TM ACTUATOR BRAKES
      3-9.3相AC油壓致動器操作/防爆和防火焰剎車

             3PHASE AC HY-THRUST TM OPERATED EXPLOSION-PROOF AND FLAME-PROOF BRAKES
      3-10.氣動和油壓操作剎車PNEUMATIC AND HYDRAULIC OPERATED BRAKES
      3-11.油壓(踏板式)剎車HYDRAULIC (PEDAL) OPERATED BRAKES
      3-12.踏板操作油壓系統加到SA , ST和ST/E剎車

              PEDAL OPERATED HYDRAULIC OVER-RIDE SYSTEM FOR ADDING TO BRAKE TYPES SA ,

              SA/M , ST AND ST/E BRAKES
      3-13.手輪和拉桿致動剎車HANDWHEEL AND LEVER APPLIED BRAKES     
      3-14.對稱和偏一邊剎車輪轂SYMMETRICAL AND OFFSET HUB BRAKE WHEELS     
      3-15.齒輪型剎車鼓連軸器GEARED BRAKE WHEEL COUPLINGS
      3-16.齒輪型剎車鼓連軸器GEARED BRAKE WHEEL COUPLINGS    
      3-17.DC磁鐵剎車(SA和SA/M箱型)整流和控制器

              DC MAGNET BRAKE (TYPES SA AND SA/M) RECTIFIERS AND CONTROLLERS      
      3-18.剎車控制箱BRAKE ENCLOSURES

BRAKE WHEEL COUPLINGS 剎車鼓連軸器

The brake wheel couplings are available for all 200S Series shoe brakes. They are useful in situations where space is limited and they also eliminate the need for expensive double shaft extensions on motors and gearboxes.

 

  • SELECTION 選用
  1. 1. Brake wheel couplìngs are selected to provide sufficient rating based on the torque rating of the brake
  2. 2. Check rating data table for required brake wheel coupling speed against allowable speed.
  3. Check rating data table for shaft diameters against coupling bore and keyway sizes. If larger bore is required,select a larger coupling.

 

NOTES: 備註

  • Torque ratings listed are typical values for the 200S Series brakes based on normal operation of d 叫ve systems. For repetitive high peak load applications please consult the factory
  • Maximum speeds (RPM) are based on maximum RIM velocity of 6000 feet per minute. Brake wheels and couplings must be balanced  if peripheral speed exceeds this value.
  • Couplings are normally furnished with an average ínterference fit of 0.0005" per inch of shaft diamete,r unless otherwise specified.
  • Double engagement brake wheel couplings require realìgnment of the brake wheel to the brake If parallel mlsalìgnment becomes excessive due to tilting of the wheel and sleeve assembly.
  • The high centrifugal forces en∞unteredin ∞uplings separate

the base 011 and thickener of general-pu巾ose greases.

Special long胡rm grease (LTG) only should be used. 

 

  • Standard coupling seals are BUNA-N material. Maximum continuous operating temperature is 250.F (121 C) and maximum intermittent (Iess than 1000 hours) operating temperature is 300.F (149.C).
  • For unlisted brake torques and coupling types,please consult the factory.
  • Met付csizes are optional.

 

  • BRAKE WHEEL COUPLlNG ORDER INFORMATION

剎車鼓連軸器訂購資料

 

SPECIFY:

(1)  Coupling  (If selecting  from the standard units shown on page 16 simply specify  the catalog number. Example

13" x 5.75" - 1025 G) or if not known please supply  the following  information:

- Brake wheel diameter and face width

- Motor HP and RPM (or speed) of shaft on which brake is mounted

- Gear ratio or shaft speeds

- Details of application